![background image](http://html.mh-extra.com/html/omron/nt15s/nt15s_operation-manual_744537203.webp)
189
Transparent Mode
Section 5-4
5.4
Function Setup Menu
The setup menu allows selection of the following parameters:
-
Parameters communication SER1
-
Parameters communication SER2
-
Date
-
Time
-
Default contrast
In addition, the version number of the operating system is displayed in the header
line.
5.4.1
Adaptation of the Parameters in the Setup Menu
Within the setup mask, the parameters can be modified by means of an editor.
Pressing of the data release key allows changing into the editor. Modifying of the
data is possible once the status LED ‘data release’ has been activated. Modifying
of the variable values is possible through the + key and - key or the numerical keys.
The input must be confirmed by pressing the enter key. If supported by the display,
the modified data will be displayed in an inverse format. To prevent incorrect or
unintentional modifications, the input must be carried out in compliance with a pre-
defined sequence which must be strictly adhered to.
5.4.2
Example of a Properly Performed Modification!
1. After having switched on the device, the enter key must be pressed immediately
once the prompt is being displayed. The setup mask will appear on the display.
This procedure must be carried out even if the parameters are to be viewed only.
2. It is possible to exit the menu by means of the enter key without modifying the
menu. Upon pressing the data release key, the LED integrated in the key will be
activated, thus signalling the editing mode within the transparent mode of oper-
ation.
3. The cursor will be positioned on the first editable variable and will be flashing.
The cursor keys allow selection of the variable to be modified.
4. Numerical values may now be entered through the numerical keypad, texts are
selected using the +,- keys.
5. The enter key must be pressed following each input. After a valid input, the
cursor will appear on the next editable input field.
6. In case of interface parameters, the variable to be modified must be set to ‘SET-
UP DATA’, thereby preventing an accidental input. The selection ‘SETUP
DATA’ must be made separately for the communication interface SER1 and the
download/printer interface SER2.
7. Exiting of the editing mode is possible by pressing the data release key once
more, the status LED will be deactivated; any modified values will still be dis-
played in an inverse format. Repeated corrections are possible using the data
release key.
Содержание NT15S
