background image

Physical Layout of the Unit

Section 2-1

11

2-1-2

 LED Indicators

RUN  (green) : Unit status indication.

ON : Indicates  that  the  unit  is  receiving  power  from  the

CQM1  power  supply,  and  that  the  unit  has  initialised
properly.

Flashing : The unit is initialising.

ERR 

(red) : General error indication.

ON :  An  internal  hardware  problem  is  detected  during

power-on initialisation (RUN LED flashing).

Errors  in  the  data  transmission  between  slaves  and
the master.

A  requested  change  of  operation  mode  was  not  pos-
sible.

APF 

(red) : AS-Interface power fail indication.

ON :  The supply voltage on the AS-Interface line is too low

to guarantee reliable communication.

CER 

(red) : Configuration error.

ON :  The detected actual configuration is different from the

stored ’projected’ configuration.

AUP  (yellow) : Auto-programming is available.

ON :  One  slave  is  missing,  and  can  be  replaced  by  an

identical  slave  with  address  0,  when  the  master  is  in
Protected  Mode.  The  address  will  then  automatically
be set to that of the missing slave.

CM 

(yellow) : ON : The unit is in Configuration Mode or in Setup Mode.

1. Configuration Mode.

The AS-Interface master will automatically accept new
slaves  in  the  configuration,  and  start  I/O  data  ex-
change with them.

2. Setup Mode.

The  permanent  configuration  data  in  the  CQM1-ARM
can  be  modified,  slave  addresses  and  slave  parame-
ters can be read/written.

OFF : the unit is in Protected Mode.

Содержание CQM1-ARM21























































































Отзывы: