manualshive.com logo in svg

Omicron SAA1, Дополнительный лист

Поделиться
Скачать
Omicron SAA1 Скачать руководство пользователя страница 29

SAA2 Warning Lamp 

29 

OMICRON 

5.4   

Testing 

 

WARNING 

 

 

 

Death or severe injury caused by high voltage or current possible.

 

  Do not connect the main device to the asset under test. 

  When conducting a functional check for the 

SAA2

, set the lowest possible current 

or voltage value on the main devices. 

1.  Connect the 

SAA2

 signal lamp to the main device as described in 5.3 Connection. 

2.  Push the 

Emergency Stop

 button on a signal lamp.  

Then all signal lamps should flash green. 

 

 
 
 
 
 
 

 
 

 

       Figure 13: Emergency button activation 

3.  Put the main device into safe operating condition and try to start the main device with the pressed 

Emergency Stop

 button. The test system should NOT start. 

 

WARNING 
Death or severe injury caused by high voltage or current possible.

 

  Ensure that no personnel are in the working area. 

4.  Release the 

Emergency Stop

 button and start the main device. Then the signal lamps should 

change from green to red. 

 

WARNING 
Death or severe injury caused by high voltage or current possible.

 

  Contact OMICRON technical support if you observe any other behavior 

than described in this section. 

 

 

 

 

Содержание SAA1

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды