Olivetti 3D IoT Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 77

Olivetti 3D IoT Скачать руководство пользователя страница 5

596806-02

User Manual

v

INTRODUCTION

GENERAL SAFETY PROVISIONS

Important safety-related provisions are provided in this section which must be observed when installing and
using the printer: read and follow attentively these instructions and all other information provided in this manual.

SAFETY WARNINGS

Pictograms are applied to certain parts of the printer as safety warnings, these warnings must be observed
attentively by anyone preparing to use the printer

.

HOT SURFACES

The hot surfaces warning symbol warns of the presence of devices having high temperatures.
Always exercise great care and wear safety gloves when manipulating heated components

HIGH VOLTAGE HAZARD

Exercise great caution: live electrical equipment

MOVING PARTS

Moving parts present - approach with great care

CRUSHING/PINCHING HAZARD

Do not introduce your hands into the machine while it is functioning

GROUND TERMINAL

Equipment ground connection points

REMOVAL OF MECHANICAL GUARDS PROHIBITED

Do not open the front door during the printing process. Do not remove the protective bellows of
the worm screw.

GLOVES

When carrying out preparatory procedures for printing or maintenance routines, the device may
be hot therefore you must always wear gloves to avoid burns.

READ INSTRUCTIONS

For the correct operating instructions you must read the User Manual provided on the SD Card
supplied with the product.

«
...
3
4
5
6
7
...
»

Содержание 3D IoT














































































Отзывы:

Нет отзывов