35
I
GB
F
D
E
SK
P
GR
TR
CZ
RUS
UK
PL
WARNING - Do not leave the machine
unattended when the engine is running.
Stop the engine whenever you move
away from the machine. It should also be
stopped before refuelling, before any
maintenance work is carried out or
before cleaning the machine.
- Stop the machine if the work implement
strikes a foreign body. Examine the machine
and repair any damaged parts.
- Be particularly cautious and alert while
wearing hearing protection because such
equipment may restrict your ability to hear
sounds indicating danger (calls, signals,
warnings, etc.).
- For best results always work with the engine
at full throttle and the machine moving at
low speed. The working result will never be
optimal if the ground speed is too fast.
WARNING: Never lean over the cutting
attachment guard. Stones, rubbish, etc.
can be thrown up into the eyes causing
blindness or serious injury. Do not have
the machine checked by anyone else
while you are driving it with the engine
running. Stop the machine immediately
if anyone approaches.
WARNING: Sometimes branches or grass
get caught between the guard and
cutting attachment. Always stop the
engine before cleaning.
WARNING: Do not attempt to remove the
cut material while the engine is running
or the cutting equipment is rotating, as
this can result in serious injury.
Starting
WARNING: The engine must be started in
an open or well-ventilated area. ALWAYS
REMEMBER THAT EXHAUST GASES ARE
TOXIC.
Before starting the engine:
1. Check the oil and gasoline levels.
2. Open the gasoline tap (
ON
) (1, Fig.35).
3. Set the choke (2, Fig.35) to
CLOSE
position.
4. Press the primer button 3 times at 2-second
intervals (3, Fig.36). In temperatures under
10°C, press the primer button 5 times.
5. Move the throttle (4, Fig.36) to the
FAST
position.
6. Insert the engine key (5, Fig.36).
Then perform the following operations:
Starting manually:
CAUTION - To start up manually the
machine, you must stand in the area
indicated in Fig.37.
7. Pull the starter rope (
Fig. 38
) until the first
firing of the engine is heard (no more than
five (5) pulls).
A new unit may require
additional pulls.
Never wrap the starter cord around your
hand.
When pulling the starter rope, do not use
the full extent of the rope as this can cause
the rope to break. Do not let starter rope
snap back. Hold the handle and let the rope
rewind slowly.
Starting with electric starter (56 EL):
7. Insert the ignition key (1, Fig.34) and
engage the starter motor (2) for a maximum
of 5 seconds. Repeat up to 10 times, waiting
5 seconds before the next attempt. After
that, wait at least 40 minutes to allow the
starter motor to cool. If the engine does not
start after the next 10 attempts, contact a
Servicing Dealer.
Starting with electric starter (62-70 ELD -
72 ELDT):
7.
NOTE: The electric cable is not supplied.
Plug the schuko plug in electrical source on
the machine (Fig.39). Plug the other plug in
electrical source plugged in (230 V – 50 Hz).
Then press the starter (1) for a maximum of
5 seconds, to activate the starter motor.
Repeat up to 10 times, waiting 5 seconds
before the next attempt. After that, wait at
least 40 minutes to allow the starter motor
to cool. If the engine does not start after the
next 10 attempts, contact a Servicing
Dealer. Never press the button (1) when the
engine is started, to avoid damaging it.
Содержание efco ARTIK 56
