OHAUS Pioneer PA64 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 116

background image

CHAPTER 3 MAINTENANCE PROCEDURES

Pioneer

™ Balance Service Manual

3-15

Ohaus Corporation www.ohaus.com

3.3.11 Load Cell Reassembly

– Precision Balances

Before re-assembly, take the following maintenance steps:

– Be sure all Flexures are straight, or replace them with new ones.

Place each Flexure on a clean flat surface and check that both sides rest evenly on the
surface. If a Flexure is bent even slightly, it must be replaced. (See Figure 3-23.)

– Be sure all parts are clean and free of debris.

1. Adjust the black Up/Down Stop

Screw so the Ratio Beam can
clear.

2. Insert the Ratio Beam into the

Load Cell frame. (See Figure 3-
36.)

3. Install the Service Fixture and

Hanger to the frame and the Ratio
Beam.  Hold the Hanger by hand
while inserting the two screws that
secure the Fixture to the Hanger.
Then insert the four screws that
secure the Fixture to the

Figure 3-36. Installing Ratio Beam,

clearing the Up/Down Stop Screw.

Load Cell frame and the Ratio Beam. (See Figures 3-38 and 3-39.)

Figure 3-37. Service Fixture for 150g to

410g Precision Load Cell, attached to

Hanger, Ratio Beam, and Load Cell frame.

Figure 3-38. Service Fixture for 510g to 4100g

Precision Load Cell, attached to Hanger, Ratio

Beam, and Load Cell frame.

4. Adjust the Up/Down Stop Screw so the groove is half way above and below the

stop tab. (Close it completely, then open it completely counting the turns, then
close it half-way.)

Screws
holding
Service
Fixture to
Hanger

Screws connecting
Service Fixture to Hanger

Screws connecting Service Fixture to
Ratio Beam and Load Cell frame

Screws connecting Service Fixture to
Ratio Beam and Load Cell frame

«
...
37
38
39
40
41
...
»

Содержание Pioneer PA64





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Pioneer PA64

Victoria BM 708

Бренд: ADE Страницы: 44

Бренд: Setra Systems Страницы: 32

Бренд: Minebea Intec Страницы: 64

Бренд: WAHL James Martin Страницы: 5

Бренд: Toshiba Страницы: 96

Бренд: impact Страницы: 24

Бренд: OBH Nordica Страницы: 16

Бренд: Tanita Страницы: 81

Бренд: Beurer Страницы: 122

Navigator NV1201

Бренд: OHAUS Страницы: 72

Бренд: OHAUS Страницы: 88

Бренд: Hyundai Страницы: 20

Бренд: Hobart Страницы: 16

Бренд: SAPIRHOME Страницы: 7

Бренд: lamart Страницы: 6

Бренд: Hofmann Страницы: 24

Бренд: Daga Страницы: 24

Бренд: CAS Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды