OHAUS Pioneer PA64 Скачать руководство пользователя страница 85

Страница: 85 / 116

CHAPTER 4 TESTING

Pioneer

™ Balances Service Manual

4-7

Ohaus Corporation www.ohaus.com

4.4.6 Repeatability Test

Repeatability is the Standard Deviation of a set of similar weight readings.

Requirements:

– To perform this test a single mass must be used for all readings.

– The test mass should be approximately ½ of the capacity of the instrument.

– Wear gloves when handling the mass.

Before starting a repeatability test, set up the instrument as follows:

Set Up:

Enter the menu and adjust and record the following settings:

A. Set the Filter level to medium or the center of its range.

B. Set the AZT (Auto Zero Tracking) to .5d or its lowest setting. Do not turn it off.

C. Set the instrument to display the same units as the performance specifications.

(Usually kg, g, or mg)

Record Settings:

Filter Level Setting =

____________

Auto Zero Tracking Setting =

____________

Displayed Units =

____________

Mass Used =

____________

TEST PROCEDURE:

1. Zero the instrument, if it does not read zero.

2. Using a test mass approximately half the capacity of the instrument, place the mass on

the center of platform. Record the reading on the worksheet provided.

3. Remove the mass from the platform.

4. Repeat this test starting at Step 1 until you record a total of ten readings

Fill in the worksheet (Table 4-4) with the ten (10) readings

Содержание Pioneer PA64





















































































































Результаты поиска

Содержание Pioneer PA64

Отзывы:

Похожие инструкции для Pioneer PA64

Бренды по названию

Популярные бренды

OHAUS Pioneer PA64, Руководство по обслуживанию

Результаты поиска

Содержание Pioneer PA64

Отзывы:

Похожие инструкции для Pioneer PA64

Бренды по названию

Популярные бренды