OHAUS Pioneer PA64 Скачать руководство пользователя страница 78

Страница: 78 / 116

CHAPTER 3 MAINTENANCE PROCEDURES

Ohaus Corporation www.ohaus.com

3-54

Pioneer

™ Balances Service Manual

3.3.34 Setting the Up/Down Stop Screw on Block Style Load Cells

This procedure is required when either the Ratio Beam has been removed or replaced, or when
the Position Sensor has been replaced.

1. Disconnect the Ribbon Cable from the Contact Board to the Load Cell PCB.

2. The Load Cell must be completely reassembled and installed in the balance

Housing.

3. Plug the Ribbon Cable from the top of the Load Cell PCB into the Main PC Board.

4. Attach a Voltmeter (DC range) to the pins on the Load Cell PCB test connector, as

shown in Figure 3-159.

Apply power to the balance.

Figure 3-159. Load Cell PCB Test Connector.

Figure 3-160. Test Connector Detail.

6. Measure the voltage with the Ratio Beam at the

bottom

of the Up/Down Stop Screw.

7. Carefully lift the Ratio Beam with

thumb and forefinger until it is at
the top of the Up/Down Stop
Screw. Measure the voltage again.

8. If the two voltage values either side

of zero are not of the same
magnitude, e.g. +2 V and

–1.6 V,

the vertical stop must be adjusted
until the values are symmetrical.
Maximum difference is 0.2 Volts.

9. To adjust the Up/Down Stop Screw,

Figure 3-161. Up/Down Stop Screw

turn the Screw and repeat Steps 2 and 3 until the readings are within specifications.
(See Figure 3-161.)

Test Connector

To Voltmeter

Содержание Pioneer PA64





















































































































Результаты поиска

Содержание Pioneer PA64

Отзывы:

Похожие инструкции для Pioneer PA64

Бренды по названию

Популярные бренды

OHAUS Pioneer PA64, Руководство по обслуживанию

Результаты поиска

Содержание Pioneer PA64

Отзывы:

Похожие инструкции для Pioneer PA64

Бренды по названию

Популярные бренды