manualshive.com logo in svg

NXP Semiconductors MPC5566, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MPC5566 Скачать руководство пользователя страница 349

Error Correction Status Module (ECSM)

MPC5566 Microcontroller Reference Manual, Rev. 2

8-6

Freescale Semiconductor

data write cycles, subsequent reads of the corrupt address locations generate ECC events, such as 
double-bit noncorrectable errors that are terminated with an error response.

If an attempt to force a non-correctable error (by asserting ECSM_EEGR[FRCNCI] or 
ECSM_EEGR[FRC1NCI]) and the ECSM_EEGR[ERRBIT] equals 64, then no data error is generated. 

NOTE

Only values {0,0}, {1,0} and {0,1} are allowed for the two control bit 
enables {FRCNCI, FR1NCI}. The value {1,1} causes undefined results.

Base + 0x004A

Access: Read/Write

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

0

0

FRC

NCI

FR1

NCI

0

ERRBIT[0:6]

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 8-3. ECC Error Generation (ECSM_EEGR) Register

Table 8-4. ECSM_EEGR Field Definitions

Field

Description

0–5

Reserved.

6

FRCNCI

Force internal SRAM continuous noncorrectable data errors. 
0 No internal SRAM continuous 2-bit data errors are generated.
1 2-bit data errors in the internal SRAM are continuously generated.
The assertion of this bit forces the internal SRAM controller to create 2-bit data errors, as defined by the bit position 
specified in ERRBIT[0:6] and the overall odd parity bit, continuously on every write operation.
The normal ECC generation takes place in the RAM controller, but then the polarity of the bit position defined by 
ERRBIT and the overall odd parity bit are inverted to introduce a 2-bit ECC error in the RAM.

7

FR1NCI

Force internal SRAM one noncorrectable data errors. 
0 No internal SRAM single 2-bit data errors are generated.
1 One 2-bit data error in internal SRAM is generated.
The assertion of this bit forces the internal SRAM controller to create one 2-bit data error, as defined by the bit 
position specified in ERRBIT[0:6] and the overall odd parity bit, on the first write operation after this bit is set.
The normal ECC generation takes place in the internal SRAM controller, but then the polarity of the bit position 
defined by ERRBIT and the overall odd parity bit are inverted to introduce a 2-bit ECC error in the RAM.
After this bit has been enabled to generate a single 2-bit error, it must be cleared before being set again to properly 
re-enable the error generation logic.

Содержание MPC5566





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды