manualshive.com logo in svg

NXP Semiconductors MPC5566, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MPC5566 Скачать руководство пользователя страница 1049

MPC5566 Microcontroller Reference Manual, Rev. 2

22-12

Freescale Semiconductor

 

22.3.3.2

Control Register (CAN

x

_CR)

CAN

x

_CR is defined for specific FlexCAN2 control features related to the CAN bus, such as bit-rate, 

programmable sampling point within an RX bit, loop-back mode, listen-only mode, bus off recovery 
behavior, and interrupt enabling (for example, bus-off, error). It also determines the division factor for the 
clock prescaler. BOFFMSK, ERRMSK, and BOFFREC bits can be accessed at any time. CANx_CR is 
unaffected by soft reset, which occurs when CAN_MCR[SOFTRST] is asserted. 

14

SRXDIS

This bit defines whether FlexCAN is allowed to receive frames transmitted by itself. If this bit is
asserted, frames transmitted by the module is not stored in any MB, regardless if the MB is
programmed with an ID that matches the transmitted frame, and no interrupt flag or interrupt signal
is generated due to the frame reception.
1 = Self reception disabled
0 = Self reception enabled

15

MBFEN

Message buffer filter enable. This bit provides the capability of enabling either individual masking of every 
message buffer, or global masking of message buffers. 

By negating MBFEN, global masking is enabled and FlexCAN uses the Rx ID masking scheme of 
RXGMASK, RX14MASK and RX15MASK. MB14 and MB15 have individual masks and the others share the 
global mask. The scheme does not provide a reception queue; i.e. a received message always fills the first 
matching buffer, setting the CODE field to overrun if the buffer contained an unread message. See 

Section 22.3.3.4, “RX Mask Registers

” for more information. Use global masking for compatibility with 

previous FlexCAN versions, which negates MBFEN at reset to retain compatibility with existing software. 

By asserting MBFEN, individual Rx ID masking and the reception queue features are enabled. In this 
scheme, individual receive mask registers (RXIM[0-63]) are provided for each MB. Upon receiving a 
message, FlexCAN searches the reception queue for the first empty matching MB. See 

Section 22.3.3.5, “RX 

Individual Mask Registers (CANx_RXIMR0 through CANx_RXIMR63)

” and 

Section 22.4.3.2, “Reception 

Queue

” for more information. 

0 = Individual RX masking and reception queue features are disabled (thus the device is compatible with 

previous FlexCAN versions, i.e. one global mask register is used).

1 = Individual RX masking and reception queue features are enabled.

16–25

Reserved.

26–31

MAXMB[0:5]

Maximum number of message buffers. This 6-bit field defines the maximum number of message buffers of 
the FlexCAN2 module. The reset value (0x0F) is equivalent to 16 MB configuration. FlexCAN must be in 
freeze mode before changing this value.

Note:

MAXMB must be less than or equal to the number of available message buffers. FlexCAN2 cannot 
transmit or receive frames if this value is greater than the number of available message buffers.

Table 22-7. CAN

x

_MCR Field Descriptions (continued)

Field

Description

Maximum MBs in use

MAXMB

1

+

=

Содержание MPC5566





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды