manualshive.com logo in svg

NXP Semiconductors MC9S12VRP64, Руководство владельца

Поделиться
Скачать
NXP Semiconductors MC9S12VRP64 Скачать руководство пользователя страница 438

64 KByte Flash Module (S12FTMRG64K4KV2) 

MC9S12VRP Family Reference Manual Rev. 1.3

438

NXP Semiconductors

18.1

Introduction

The FTMRG64K4K module implements the following:

•

64Kbytes of P-Flash (Program Flash) memory

•

4Kbytes of D-Flash memory

The Flash memory is ideal for single-supply applications allowing for field reprogramming without 
requiring external high voltage sources for program or erase operations. The Flash module includes a 
memory controller that executes commands to modify Flash memory contents. The user interface to the 
memory controller consists of the indexed Flash Common Command Object (FCCOB) register which is 
written to with the command, global address, data, and any required command parameters. The memory 
controller must complete the execution of a command before the FCCOB register can be written to with a 
new command.

CAUTION

A Flash word or phrase must be in the erased state before being 
programmed. Cumulative programming of bits within a Flash word or 
phrase is not allowed. 

The Flash memory may be read as bytes and aligned words. Read access time is one bus cycle for bytes 
and aligned words. For misaligned words access, the CPU has to perform twice the byte read access 
command. For Flash memory, an erased bit reads 1 and a programmed bit reads 0.

It is possible to read from P-Flash memory while some commands are executing on D-Flash memory. It 
is not possible to read from D-Flash memory while a command is executing on P-Flash memory. 
Simultaneous P-Flash and D-Flash operations are discussed in 

Section 18.4.5

.

Both P-Flash and D-Flash memories are implemented with Error Correction Codes (ECC) that can resolve 
single bit faults and detect double bit faults. For P-Flash memory, the ECC implementation requires that 
programming be done on an aligned 8 byte basis (a Flash phrase). Since P-Flash memory is always read 
by half-phrase, only one single bit fault in an aligned 4 byte half-phrase containing the byte or word 
accessed will be corrected.

18.1.1

Glossary

Command Write Sequence

 — An MCU instruction sequence to execute built-in algorithms (including 

program and erase) on the Flash memory.

D-Flash Memory 

— The D-Flash memory constitutes the nonvolatile memory store for data.

D-Flash Sector

 — The D-Flash sector is the smallest portion of the D-Flash memory that can be erased. 

The D-Flash sector consists of 256 bytes.

NVM Command Mode

 — An NVM mode using the CPU to setup the FCCOB register to pass parameters 

required for Flash command execution.

Phrase

 — An aligned group of four 16-bit words within the P-Flash memory. Each phrase includes two 

sets of aligned double words with each set including 7 ECC bits for single bit fault correction and double 
bit fault detection within each double word.

Содержание MC9S12VRP64












































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды