Numatics G3 Series EtherNet/IP, Техническое руководство

Страница: 24 / 154

G3 Series EtherNet/IP TM Technical Manual
Page 4-24
TDG3EPTM1-9EN 05/18
Subject to change without notice
www.asco.com/g3
4.6 Power Consumption
Power Connection
C
ENELEC
Pin No.
Function Description
1
+24 VDC
(Valves and Outputs)
Voltage used to power outputs
(valve coils and discrete outputs) SW
2
+24 VDC
(Node and Inputs)
Voltage used to power discrete inputs and
node electronics UNSW
3
0 VDC Common
(Node and Inputs)
0 VDC (-V) Voltage used to power discrete inputs and
node electronics UNSW
4
0 VDC Common
(Valves and Outputs)
0 VDC (-V) Voltage used to power outputs
(valve coils and discrete outputs) SW
Power Rating
• For maximum supply current capability please refer to page 59.
• Loads should not draw more than 0.5 Amps of current from any one individual discrete output point (Contact
factory for higher current capability requirements).
Component Voltage Tolerance
+24VDC
(Valves and Outputs)
Pins 1 and 4
+24VDC
(Node and Inputs)
Pins 2 and 3
Current Power Current Power
Solenoid Valve Coil 501 (Each) 24 VDC +10%/-15% 0.03 A 0.80 W 0 A 0 W
Solenoid Valve Coil 502 (Each) 24 VDC +10%/-15% 0.06 A 1.30 W 0 A 0 W
Solenoid Valve Coil 503 (Each) 24 VDC +10%/-15% 0.07 A 1.70 W 0 A 0 W
Solenoid Valve Coil 2002 (Each) 24 VDC +10%/-15% 0.02 A 0.48 W 0 A 0 W
Solenoid Valve Coil 2005 (Each) 24 VDC +10%/-15% 0.06 A 1.44 W 0 A 0 W
Solenoid Valve Coil 2012 (Each) 24 VDC +10%/-15% 0.11 A 2.64 W 0 A 0 W
Solenoid Valve Coil 2035 (Each) 24 VDC +10%/-15% 0.11 A 2.64 W 0 A 0 W
Solenoid Valve Coil ISO 5599/2- SPA 24 VDC +10%/-15% 0.17 A 4.08 W 0 A 0 W
Valve Adapter (Driver) 24 VDC +/- 10% 0.03A 0.72 W 0.02 A 0.48 W
Digital Module 24 VDC +/- 10% 0.04 A 0.96 W 0.05 A * 1.20 W *
Analog Module 24 VDC +/- 10% 0.01 A 0.24 W 0.08 A * 1.92 W *
Sub-Bus Hub 24 VDC +/- 10% 0 A 0 W 0.06 A 1.44 W *
RTD Module 24 VDC +/- 10% 0.01 A 0.24 W 0.06 A 1.44 W *
Communication Module (Node) 24 VDC +/- 10% 0.01 A 0.24 W 0.07A * 1.68 W *
Sub-Bus Valve Module 24 VDC +/- 10% 0.01 A 0.24 W 0.03 A * 0.72 W *
Auto Recovery Module (ARM) 24 VDC +/- 10% 0 A 0 W 0.03 A 0.72 W
Manual Configuration Module (MCM) 24 VDC +/- 10% 0 A 0 W 0.03 A 0.72 W
* Current depends on graphic display brightness setting. Max. value shown with high brightness.
Values decrease by approx. 5% for Medium and 11% for Low brightness settings.
NOTE!
• Total power consumption for each Discrete I/O point is dependent on the
specific current draw of input sensor devices and output loads.