NTT docomo FOMA SO706i, Инструкция по эксплуатации

Страница: 324 / 485

322
Netw
ork
Ser
vices
*5: This function shows names which are checked against the name of data saved in phonebook with each number/
address and converted into that name, when phone numbers on dialing/incoming, numbers on sending/receiving or
addresses on sending/receiving are saved in phonebook.
*6: A is applied when the terminal of the sender does not support 2in1.
*7: The destination address is selectable from B setting phonebook when composing a new mail in Dual mode,
however, please note that the mail is sent from Address A. Note that if you forward a mail to Address B in Dual mode,
the mail is sent from Address A.
*8: Unavailable for each i-
α
ppli standby screen, Mail-linked i-
α
ppli and the i-
α
ppli used with mail functions.
*9: Unavailable for i-
α
ppli standby screen.
Using 2in1
Set 2in1 to ON and perform settings operations.
1
i
“SERVICE” “2in1 setting” Enter
your security code “YES” Select any
item:
■ When 2in1 is set to ON
After entering the security code, 2in1 setting
screen appears without showing the screen to
confirm whether to set 2in1 to ON is not displayed.
Mode switching …… Selects the 2in1 mode from “A
mode/B mode/Dual mode”.
“About Modes”
→ p.320
Phonebook 2in1 setting
Phonebook 2in1 setting …… Highlight the
phonebook entry to set and press
d
(Switch)
to select the mode, then press
o
(Finish).
The mode switches as follows each time you
press
d
(Switch): (A mode) → (B
mode) → (Dual mode)
How to search the phonebook → p.73
Group 2in1 setting
……
Highlight the group to
set and press
d
(Switch) to select the mode,
then press
o
(Finish).
The mode switches as follows each time you
press
d
(Switch): no setting
→
(Dual
mode) → (A mode) → (B mode)
Stand-by display
……
Sets the standby screen
displayed in B mode or Dual mode respectively.
→
p.89
“
★
” appears for the changed item. To reset the
setting, press
o
(Release).
Set call/receive No.
Disp. call/receive No.
……
Sets to display the
information (name, phone number, mail
address, etc.) of “Number A (Address A)” and
“Number B (Address B)” in different font color
to distinguish when making/receiving a call.
Press
o
(Switch) to switch the color of the
pallet (16 colors or 256 colors).
Press
p
(Reset) to reset to the default setting.
Ringtone for Number B
……
Set the incoming
operation (ring tone, image, illumination,
vibration, answer message) performed when
receiving a voice call, videophone call or mail
(Ring tone, illumination and vibration can be
set in Mail (recv.)).
Voice call (recv.), V.phone (recv.), Mail
(recv.)
……
• “Ring tone”: Go to Step 2 in “Changing the
Ring Tone” (p.82).
• “Image”: Go to Step 2 in “Changing the
Display” (p.88).
• “Illumination”: Go to Step that comes after
selecting “Incoming Call”, “Incoming
V.phone” or “Mail receiving” in Step 1 of
“Setting the Illumination Flashing” (p.92).
• “Vibrator”: Go to Step 2 in “Setting the
Vibration to Notify You of Incoming Calls”
(p.84).
• “Answer message”: Go to the subsequent
step after selecting “ON” in “Setting Record
message” (p.64).
2in1 function OFF
……
Sets 2in1 to OFF.
Rcv. avoid. setting …… Restricts incoming calls for
Number A and Number B.
Change rcv. avoid. …… Sets the Rcv. avoid.
setting for Number A and Number B.
Check rcv. avoid. …… Checks the Rcv. avoid.
setting for Number A and Number B.
Mode link …… Sets the linkage for changing
2in1 mode and Rcv. avoid. setting. Incoming
calls only for Number A are accepted in A
mode, incoming calls only for Number B are
accepted in B mode, and incoming calls for
both mode are accepted in Dual mode.
* When the function is activated, you cannot
switch the mode with “ ” displayed.
Rcv. avoid. (abroad) …… Sets the Rcv. avoid.
setting overseas (when Mode link is active, the
Rcv. avoid. (abroad) is disabled).