Novanta i401 Скачать руководство пользователя страница 120

Страница: 120 / 133

BEAM DELIVERY OPTICS

PAGE

120

Beam delivery optics

Troubleshooting

Symptom:
The laser loses power over time; laser output power must be increased to maintain performance.

Possible Causes:

•

Beam delivery optics are coated by vapor residue or debris.

Shut down the laser and carefully inspect each optic in the beam delivery path. If the optic requires

cleaning, refer to Maintenance for cleaning instructions. Use only recommended cleaning materials (see

Table 4-1) to prevent scratching delicate optical surfaces. If the focusing optic is pitted, it must be

replaced immediately. Because of the extremely high-power density of I401 lasers, pits or debris on the

lens surface may absorb enough energy from the focused beam to crack the lens. If this happens, other

optics in the beam path may be contaminated or damaged as well.

Warning: Serious Personal Injury

Ensure that DC power to the laser is turned off and locked out before inspecting optical

components in the beam path. Invisible CO2 laser radiation is emitted through the aperture.

Corneal damage or blindness may result from exposure to laser radiation.

Warning: Serious Personal Injury

The use of aerosol dusters containing difluoroethane causes “blooming”, a condition that

significantly expands and scatters the laser beam. This beam expansion can affect mode quality

and/or cause laser energy to extend beyond the confines of optical elements in the system,

possibly damaging acrylic safety shielding. Do not use air dusters containing difluoroethane in

any area adjacent to CO

laser systems because difluoroethane persists for long time periods

over wide areas.

Caution: Possible Equipment Damage

If you operate your laser or marking head in a dirty or dusty environment, contact Novanta

about the risks of doing so and precautions you can take to increase the longevity of your laser,

marking head, and associated optical components.

Содержание i401






































































































































Результаты поиска

Содержание i401

Отзывы:

Похожие инструкции для i401

Бренды по названию

Популярные бренды

Novanta i401, Руководство пользователя

Результаты поиска

Содержание i401

Отзывы:

Похожие инструкции для i401

Бренды по названию

Популярные бренды