Novanta i401 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 133

background image

HOME PAGE LAYOUT

PAGE

|

85

Displays the heat sink temperature of each RF module.

Relative Humidity:
Displays the measured relative humidity (RH) within the i401 laser housing. When purge gas is flowing,

the RH value should drop to 0% (± 10%) within 10–15 minutes. If the relative humidity never drops below

approximately 10%, then slightly increase the purge gas flow rate.

Flow Sensor Temp*:
Displays cooling system temperature measured after the RF amplifier modules.

Important Note: The low Sensor Temp value is not a measurement of coolant temperature and

should not be used to adjust the chiller’s setpoint.

Internal Tickle Setting:
Indicates that tickle is active (ON) and displays the actual tickle setting.

5 Seconds Delay Setting:
Indicates that the five-second delay is active (Enabled).

Error message area:
Hard faults (those that require a power cycle), are annunciated in the upper (red) error message area

while warnings are described in the lower (yellow) message area. If a fault occurs before the web

interface is active, the fault or warning message is displayed; however, no other operating data is

archived or displayed.

Reference: i401 Diagram:
Hyperlink to an illustration showing various i401 modules and their location inside the laser housing.

Configure IP Address link:
Click this link to change the laser’s factory-default IP address (192.168.50.50). See the Changing the i401’s

IP address section for details.

«
...
83
84
85
86
87
...
»

Содержание i401






































































































































Отзывы:

Нет отзывов

Похожие инструкции для i401

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

Бренд: Sanmenxia Страницы: 17

Бренд: SANKO Страницы: 25

Бренд: Samson Страницы: 2

Бренд: Olimpus Страницы: 12

Бренд: Energometrika Страницы: 39

Бренд: Laser Technology Страницы: 80

Бренд: JBM Страницы: 4

GRAND RHAPSODY PIANO

Бренд: Waves Страницы: 19

Бренд: EIJKELKAMP Страницы: 11

Бренд: PTC Instruments Страницы: 2

KS-PH-221-DELUXE

Бренд: Kensington Страницы: 14

Бренд: INTERSPIRO Страницы: 76

Бренд: Net2Edge Страницы: 37

Бренд: SPEEDMATE Страницы: 3

Бренд: East Tester Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды