Novanta i401 Скачать руководство пользователя страница 70

Страница: 70 / 133

PAGE

Output

Common

Use this pin to complete the return path for output connections (Pin 6, 7,

8, 14, or 15). The Output Common line is protected by a 0.3 A self-

resetting fuse.

Shutter Open

output

This bi-directional switched output is internally connected to Pin 13,

Output Common, when Remote Interlock

and

Shutter Open Request

signals are present (RDY indicator illuminated yellow and SHT indicator

blue) to indicate that the shutter is open, and lasing is enabled This output

is open (high impedance) when the laser is disabled (SHT indicator Off).

Interlock

Open output

This bi-directional switched output is internally connected to Pin 13,

Output Common, when remote interlock circuitry is open (INT indicator

illuminated red), indicating that lasing is disabled. The output is open (high

impedance) when lasing is enabled (INT indicator green).

Input/output signals

The I401 i401’s input/output signals are divided into three categories: auxiliary DC power, input signals,

and output signals. Signals in each category are fully described in the following sections.

Auxiliary DC power

i401 User I/O connector provides auxiliary DC power for driving external inputs or outputs connected to

the User I/O port. Pin 4, +5 VDC Auxiliary Power, and Pin 5, +24 VDC Auxiliary Power, are protected by

self-resetting fuses rated at 0.5 A. Pin 12, Auxiliary DC Power Ground, is connected to chassis ground

while all other User I/O pins are floating with respect to chassis ground. Figure 3-6 illustrates I401’s

internal DC supply wiring.

Содержание i401






































































































































Результаты поиска

Содержание i401

Отзывы:

Похожие инструкции для i401

Бренды по названию

Популярные бренды

Novanta i401, Руководство пользователя

Результаты поиска

Содержание i401

Отзывы:

Похожие инструкции для i401

Бренды по названию

Популярные бренды