Novanta i401 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 133

background image

DC POWER/DC SENSE CABLES

PAGE

|

81

DC power/DC sense cables

The DC power/DC sense cables section includes subsections:

•

DC power cables

•

DC voltage sense cable

DC power cables

The DC power cables shipped with I401 lasers are manufactured with 1/0 AWG wire to a standard length

of 2.0 m (6.5 ft) or an optional length of 5.0 m (16 ft). Nominal finished O.D. is 14.9 mm (0.586") so the

minimum bend radius must be greater than 12 cm (4.7 in). Terminals on the laser end of the cables fit the

laser’s M10 studs while terminals on the power supply ends are sized to fit M6 (0.25") bolts.
When using a power supply other than the PS-401, we recommend using remote sensing, so the power

supply output remains at a constant voltage over varying load conditions. Choose a DC supply that can

compensate for a minimum load lead loss (round trip) of 1.0 V.

Important Note:

If you lengthen the DC Power Cables shipped with the i401 laser, you must

calculate and measure the additional voltage drop to ensure that 48.0 VDC is available at the

laser’s +48V POWER terminal under full-load conditions. Depending on the additional length required,

you may need to use larger gauge (2/0) wire.

DC voltage sense cable

The DC voltage sense cable shipped with the i401 laser is matched to the length of the DC power cable—

either the standard length of 2.0 m (6.5 ft) or an optional length of 5.0 m (16 ft). The laser end of the

voltage sense cable is finished with an M10 ring terminal to fit the +48 VDC POWER terminal and an M4

spade terminal to fit the end of the –VDC GND terminal. The power supply end of the sense cable is

terminated with a 26-pin high-density D-subminiature connector that connects to the PS-401 DC power

supply. In addition to remote sensing connections, the 26-pin HD connector includes jumpers to enable

the PS-401’s Output Inhibit and Output Interlock inputs.
When using a power supply other than the PS-401, you can fabricate your own DC voltage sense cable,

or you can remove the 26-pin HD D-subminiature connector and terminate the sense cable to match

your power supply’s DC voltage sense connections.

«
...
79
80
81
82
83
...
»

Содержание i401






































































































































Отзывы:

Нет отзывов

Похожие инструкции для i401

Бренд: OHAUS Страницы: 26

Бренд: National Instruments Страницы: 15

Бренд: TA Instruments Страницы: 7

Бренд: Olimpus Страницы: 12

Бренд: Xtralis Страницы: 13

Бренд: Tektronix Страницы: 124

Бренд: Polimaster Страницы: 6

Бренд: STONEX Страницы: 99

Dakota Ultrasonics ZX-2

Бренд: ABQ Industrial Страницы: 27

Бренд: Dynojet Страницы: 88

Бренд: VP instruments Страницы: 15

Бренд: Datakom Страницы: 2

Бренд: Velleman Страницы: 38

Бренд: Rebel Страницы: 28

Бренд: VOLTCRAFT Страницы: 8

Бренд: Keysight Страницы: 42

Multimar 25 EWR

Бренд: Mahr Страницы: 20

Бренд: jbc Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды