Nordson Tribomatic 2 Скачать руководство пользователя страница 17

Страница: 17 / 73

Safety

1-11

1998 Nordson Corporation

303 815A

Issued 3/98

Manual 37-32

Table 1-1 contains the text of the safety label shipped with the

Tribomatic II automatic gun. Place it on the powder spray booth next to

the gun operator’s station. Familiarize yourself with this label. It is

provided to help you operate and maintain your equipment safely.

Table 1-1 Safety Label

Item

Part

Description

—

244 664

WARNING:

The following procedures MUST be followed when working with

this electrostatic spray equipment. Failure to follow these instructions may

result in a fire and/or serious personal injury. Display this warning on the

spray booth.

1. NO SMOKING. Keep open flames, hot surfaces, and sparks

from torches or grinding away from booth.

2. Turn the electrostatic power unit off when the spray gun is not

in use.

3. Shut down immediately in event of fire.
4. Maintain ground circuit on all conductive objects below 1 meg

ohm to prevent sparking. (ANSI/NFPA 33, Chapter 9, or local

codes)

5. Shut down operation and correct grounds if sparking occurs.
6. Install fixed fire suppression system in accordance with

ANSI/NFPA 33, Chapter 7 (or local codes), before operating

with combustible powder.

7. Install automatic flame detectors in accordance with

ANSI/NFPA 33, Chapter 7 (or local codes), before operating

automatic guns.

8. Examine all equipment at the beginning of each work period

and repair or replace any damaged, loose, or missing parts.

9. Before cleaning or performing any maintenance on the

electrostatic spray gun, turn off the power unit and ground the

nozzle. Maintain electrostatic spray equipment in accordance

with instruction manual. Do not deviate. Do not substitute

parts from other manufacturers.

10. Operator must be grounded to prevent shocks from static

electricity. Floor surface must be conductive. Footwear and

gloves must be static dissipative in accordance with ANSI

Z41-1991 (or local codes).

Continued on next page

11. Safety Labels

Содержание Tribomatic 2




















































Результаты поиска

Содержание Tribomatic 2

Отзывы:

Похожие инструкции для Tribomatic 2

Бренды по названию

Популярные бренды

Nordson Tribomatic 2, Руководство пользователя по изделию

Результаты поиска

Содержание Tribomatic 2

Отзывы:

Похожие инструкции для Tribomatic 2

Бренды по названию

Популярные бренды