Nordson Spectrum II S2-900 C Series, Инструкция по установке, эксплуатации и обслуживанию

Страница: 13 / 262

Table of Contents xi
Figure 5-24 Heater Control Window .................................................................................................... 5-22
Figure 5-25 Heater Parameters Window ............................................................................................. 5-22
Figure 5-26 Local Machine Offsets - Heater Offsets ............................................................................ 5-24
Figure 5-27 Input Temperature Offset Value ....................................................................................... 5-24
Figure 5-28 Heater Setup Window - Controlled Process Heat Enabled .............................................. 5-25
Figure 5-29 Heater Control Loop Parameters Window - Main Tab ..................................................... 5-26
Figure 5-30 Heater Control Window - Controlled Process States ....................................................... 5-27
Figure 5-31 Current Air Flow Toolbar .................................................................................................. 5-27
Figure 5-32 Fluidmove Main Window - Cool Down Button .................................................................. 5-28
Figure 5-33 Heater Cool Down Window .............................................................................................. 5-28
Figure 5-34 Adjusting the Impingement Heater Airflow (S2-900P Dual Conveyor) ............................. 5-30
Figure 5-35 Conveyor I/O Test Dialog ................................................................................................. 5-31
Figure 5-36 Pre-Dispense Lift Table Controls ...................................................................................... 5-32
Figure 5-37 Post-Dispense Lift Table Controls .................................................................................... 5-32
Figure 5-38 Dispense Lift Table Controls ............................................................................................ 5-33
Figure 5-39 Beacon Configuration Window ......................................................................................... 5-34
Figure 5-40 Beacon Configuration Window ......................................................................................... 5-35
Figure 5-41 Dispenser I/O Window ...................................................................................................... 5-36
Figure 6-1 Replacing the Purge and Scale Station Cups .................................................................... 6-5
Figure 6-2 Replacing the Purge Boot ................................................................................................... 6-6
Figure 6-3 Draining the Water Traps ................................................................................................... 6-7
Figure 6-4 Battery Maintenance Window ............................................................................................. 6-9
Figure 6-5 Battery Gauge Reset Window .......................................................................................... 6-10
Figure 6-6 Removing the X-Axis Covers ............................................................................................ 6-11
Figure 6-7 Removing the Y-Axis Covers ............................................................................................ 6-11
Figure 6-8 Removing the Rear Cable Covers .................................................................................... 6-12
Figure 6-9 Lubricating the X-Axis Linear Guides ............................................................................... 6-16
Figure 6-10 Lubricating the Y-Axis Linear Guides ............................................................................... 6-16
Figure 6-11 Tensioning the Cables ...................................................................................................... 6-17
Figure 6-12 Tensioning the Z-Axis Cables ........................................................................................... 6-18
Figure 6-13 Accessing the Linear Encoder .......................................................................................... 6-19
Figure 6-14 X-Axis Encoder Read Head Mounting Screws ................................................................. 6-20
Figure 6-15 Y-Axis Encoder Bracket .................................................................................................... 6-21
Figure 6-16 Adjusting the Y-Axis Linear Encoder Gap ........................................................................ 6-22
Figure 6-17 Adjusting the Linear Encoder Height ................................................................................ 6-23
Figure 6-18 Tensioning the Conveyor Belts ......................................................................................... 6-25
Figure 7-1 Scale Setup Menu ............................................................................................................ 7-11
Figure 7-2 Scale Error Message ........................................................................................................ 7-11
Figure 7-3 Tactile Sensor Exposed .................................................................................................... 7-13
Figure 8-1 Gaining Access to Dispensing System Components ......................................................... 8-3
Figure 8-2 Conveyor Belt Removal/Installation .................................................................................... 8-5
Figure 8-3 Lens Assembly ................................................................................................................... 8-7
Figure 8-4 Replacing the Aperture Disk ............................................................................................... 8-8
Figure 8-5 Aperture Disks .................................................................................................................... 8-8
Figure 8-6 Camera Lens Replacement ................................................................................................ 8-9
Figure 8-7 Replacing the Height Sensor Probe ................................................................................. 8-10
Figure 8-8 Rear Cabinet ..................................................................................................................... 8-12
Figure 8-9 Main PWA Fuse Location ................................................................................................. 8-13
Figure 8-10 PDHC Fuse Location ........................................................................................................ 8-13
Figure 8-11 Replacing a Panel-Mounted Fuse .................................................................................... 8-15
Figure 9-1 S2-900 System Dimensions (1 of 2) ................................................................................... 9-4
Figure 9-2 S2-900 System Dimensions (2 of 2) ................................................................................... 9-5
Figure 9-3 S2-9XXC System Dimensions (1 of 2) ............................................................................... 9-6
Figure 9-4 S2-9XXC System Dimensions (2 of 2) ............................................................................... 9-7