Nordson Encore Select HD Скачать руководство пользователя страница 35

Страница: 35 / 57

6-1

Troubleshooting

1620445-03

Section 6

Troubleshooting

WARNING:

Allow only qualified personnel to perform the following tasks. Follow the

safety instructions in this document and all other related documentation.

WARNING:

Before making repairs to the controller or spray gun, shut off system power

and disconnect the power cord. Shut off the compressed air supply to the system and

relieve the system pressure. Failure to observe this warning could result in personal

injury.

These troubleshooting procedures cover only the most common problems. If you cannot

solve a problem with the information given here, contact Nordson technical support at

(800) 433-9319 or your local Nordson representative for help.

General Troubleshooting Chart

Problem

Possible Cause

Corrective Action

1. Uneven pattern,

unsteady or inadequate

powder flow

Blockage in spray gun, powder

feed hose, or pump

1. Purge the spray gun. Remove the nozzle and

electrode assembly and clean them.

2. Disconnect the powder feed hose from the

spray gun and blow out the powder tube with an

air gun.

3. Disconnect the feed hose from the pump and

spray gun and blow out the feed hose. Replace

the feed hose if it is clogged with powder.

4. Disassemble and clean the pump.

Nozzle, deflector, or electrode

assembly worn, affecting pattern

Remove, clean, and inspect the nozzle, deflector,

and electrode assembly. Replace worn parts as

necessary.
If excessive wear or impact fusion is a problem,

reduce the flow rate and atomizing air flow.

Continued...

Содержание Encore Select HD


























































Результаты поиска

Содержание Encore Select HD

Отзывы:

Бренды по названию

Популярные бренды

Nordson Encore Select HD, Руководство пользователя по изделию

Результаты поиска

Содержание Encore Select HD

Отзывы:

Бренды по названию

Популярные бренды