Nordson Asymtek Spectrum S-920 Скачать руководство пользователя страница 96

Страница: 96 / 238

4-30

Power-Up

and

Testing

4.10.9 Tactile Sensor

Perform the following procedures to make sure that the Tactile Sensor is functioning properly.

NOTE

The following procedure assumes the dispensing system is on and FmXP is running.

Verify your dispensing system has been configured for the type of Needle Sensor installed
as follows:

In the FmXP main Window, click on

Configuration > Machine Offsets > Machine

Offsets Parameters

In the Machine Offsets Parameters dialog box (Figure 4-19), verify the sensor type
installed on your system.

If necessary, click on the arrow in the Sensor Type box and select the correct
sensor type.

Click on

to return to the Main Window.

Figure 4-19 Machine Offsets Parameters Dialog Box

In the FmXP Main Window, click on

Tools

In the Tools Window, click on

I/O Test

and then on

Dispenser

Содержание Asymtek Spectrum S-920















































































































































































































































Результаты поиска

Содержание Asymtek Spectrum S-920

Отзывы:

Бренды по названию

Популярные бренды

Nordson Asymtek Spectrum S-920, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Asymtek Spectrum S-920

Отзывы:

Бренды по названию

Популярные бренды