background image

 

 

 

 

1 of 36 

Palletizer for AUBO Robots - Installation Manual 

 Ver. 1.7  

 

 

 

Copyright 

Copyright © 2020 Nordbo Robotics A/S. All Rights Reserved. No part of this manual may be reproduced 
or  transmitted  in  any  form  or  by  any  means,  electronic  or  mechanical,  including  photocopying  and 
recording, for any purpose without the express written permission of Nordbo Robotics A/S. 

 

 

Disclaimer 

The information provided in this documentation contains general descriptions of use, of one or more of 

Nordbo  Robotics’  products.  Following  this  documents  instruction  for  installation  and use  must not  be 

considered a substitute for making a risk assessment and testing the specific application and setup. Neither 
Nordbo Robotics nor any of our affiliates or subsidiaries shall be held responsible for the consequences 
that arise from misuse of 

 or misunderstanding

 any information stated in this document.  

 
If  any  instructions  are  cons

idered  unclear  it  is  the user’s  responsibility to  contact  Nordbo Robotics  for 

clarification of the issue(s) before making use of said unclear instructions. 
 
If the user has any suggestions for improvements, amendments or if errors have been found in this release, 
please notify Nordbo Robotics. 
Nordbo Robotics reserves the right to make refinements or changes without notice. 
 
 

Contact  

Nordbo Robotics A/S 
Agerhatten 27A Entrance 4 
5220 Odense, Denmark 
 
Phone: +45 81 81 98 81 
Mail: [email protected] 
 

 

Содержание AUBO






































Отзывы: