Nolan N40 5, Инструкция по эксплуатации

Страница: 4 / 16

“MICROLOCK
2
” RETENTION SYSTEM
Your new helmet is equipped with the exclusive “Microlock ” retention system, which is
one of the most comfortable and modern systems available today thanks to its microme-
tric regulation. In order to have the maximum protection and to appreciate the advanta-
ges of the “Microlock ” system, carefully read the instructions contained in this label. Put
your new on, making sure the size is correct (see enclosed instructions manual).
1. Attach the “Microlock ” by inserting the dented tongue in the buckle
➊
.
Warning: Do not twist the strap; the dented part of the tongue must be facing the out-
side of the helmet.
Pull on the chin strap to make sure the locking mechanism is engaged.
2. Press the dented tongue completely, until you feel the strap press against your cheek.
Warning: The tongue should not move freely in the locking mechanism.
3. Now try to take off your helmet by puling it from the back edge, rotating it towards the
front; the helmet must remain well fixed on your head (see enclosed instructions).
4. If while performing step 3 you notice that the chin strap is too loose (this can be deter-
mined by insufficient pressure on the jaw when the dented tongue is fully inserted in
the locking mechanism), then the strap must be pre-adjusted (shorten the chin strap).
If while performing step 3 you notice that the chin strap is too tight (this condition can
be determined if the chin strap is too tight when the dented tongue is on the third or
fourth click), then the chin strap must be lengthened.
5. To make a pre-adjustment, release the helmet by lifting the red lever. Slip the helmet
off
➋
.
Adjust the chin strap length by passing the strap through the metal adjusting buckle
➌
.
6. Repeat steps 1 through 3 taking care that the dented tongue has effected at least 5
clicks into the body of the locking mechanism.
(We recommend performing the pre-adjustment by sliding the fastening flap by least
5 notches so as to make the most of the adjustment function of the “Microlock
system. By sliding or releasing the fastening flap by one notch as to the pre-adju-
stment, the system ensures the best comfort guarantying the fastening safety).
7. WARNING!!! LIFT THE RED LEVER ONLY WHEN YOU ARE REMOVING YOUR HEL-
MET! NEVER RELEASE THE LEVER WHILE DRIVING!
CARE OF “MICROLOCK ” RETENTION SYSTEM
The effectiveness of the adjustment and retention system can be impaired by dust or
sand. We suggest periodic cleaning of the “Microlock ” retention system using only a
solution of luke-warm water and neutral soap.
USE NOT SOLVENT, DO NOT LUBRICATE.
Manipulations or unusual events, which can compromise the working of the retention
system cannot be excluded.
If the “Microlock ” system is not functioning properly discontinue the use of the helmet.
4
GB D
“MICROLOCK ” RETENTION SYSTEM
Your new helmet is equipped with the exclusive “Microlock
2
” retention system, which is
one of the most comfortable and modern systems available today thanks to its microme-
tric regulation. In order to have the maximum protection and to appreciate the advanta-
ges of the “Microlock 2 ” system, carefully read the instructions contained in this label. Put
your new Nolan on, making sure the size is correct (see enclosed instructions manual).
1. Attach the “Microlock
2 ” by inserting the dented tongue in the buckle
➊
.
Warning: Do not twist the strap; the dented part of the tongue must be facing the out-
side of the helmet.
Pull on the chin strap to make sure the locking mechanism is engaged.
2. Press the dented tongue completely, until you feel the strap press against your cheek.
Warning: The tongue should not move freely in the locking mechanism.
3. Now try to take off your helmet by puling it from the back edge, rotating it towards the
front; the helmet must remain well fixed on your head (see enclosed instructions).
4. If while performing step 3 you notice that the chin strap is too loose (this can be deter-
mined by insufficient pressure on the jaw when the dented tongue is fully inserted in
the locking mechanism), then the strap must be pre-adjusted (shorten the chin strap).
If while performing step 3 you notice that the chin strap is too tight (this condition can
be determined if the chin strap is too tight when the dented tongue is on the third or
fourth click), then the chin strap must be lengthened.
5. To make a pre-adjustment, release the helmet by lifting the red lever. Slip the helmet
off
➋
.
Adjust the chin strap length by passing the strap through the metal adjusting buckle
➌
.
6. Repeat steps 1 through 3 taking care that the dented tongue has effected at least 5
clicks into the body of the locking mechanism.
(We recommend performing the pre-adjustment by sliding the fastening flap by least
5 notches so as to make the most of the adjustment function of the “Microlock
2
“
system. By sliding or releasing the fastening flap by one notch as to the pre-adju-
stment, the system ensures the best comfort guarantying the fastening safety).
7. WARNING!!! LIFT THE RED LEVER ONLY WHEN YOU ARE REMOVING YOUR HEL-
MET! NEVER RELEASE THE LEVER WHILE DRIVING!
CARE OF “MICROLOCK 2 ” RETENTION SYSTEM
The effectiveness of the adjustment and retention system can be impaired by dust or
sand. We suggest periodic cleaning of the “Microlock 2 ” retention system using only a
solution of luke-warm water and neutral soap.
USE NOT SOLVENT, DO NOT LUBRICATE.
Manipulations or unusual events, which can compromise the working of the retention
system cannot be excluded.
If the “Microlock 2 ” system is not functioning properly discontinue the use of the helmet.
4
GB
1
1
1
1
1
1
1
1 ’’