manualshive.com logo in svg

Nokia ESB26, Руководство пользователя

Nokia ESB26 - качественный смартфон с широким набором функций. Чтобы ознакомиться с ними подробнее, скачайте бесплатный руководство пользователя с manualshive.com. В этом руководстве вы найдете все необходимые инструкции и советы для использования этого устройства. Не упустите возможность ознакомиться с ним!

Поделиться
Скачать
background image

7. 

Link Aggregation Groups (LAGs) 

MN700004 Rev 01 

50

Feature Overview 

Static Link Aggregation Groups (LAGs) 

Static LAGs provide the ability to treat multiple switch ports as one switch port. These port 
groups act as a single logical port for high-bandwidth connections between two network 
devices. A static LAG balances the traffic load across the links in the channel. If a physical 
link within the static LAG fails, traffic previously carried over the failed link is moved to the 
remaining links. Most protocols operate over either single ports or aggregated switch ports 
and do not recognize the physical ports within the port group.  

A static LAG consists of individual Fast Ethernet links bundled into a single logical link as 
shown in Figure 7-1: "Four Ports Combined into a Link Aggregation Group".  

Benefits 

Static LAGs provide the following benefits: 

•

 

Increased bandwidth 

The capacity of multiple interfaces is combined into one logical link. Besides 
increasing bandwidth, link aggregation also provides intermediate data rate 
levels between the standard data rates of 10 Mbps, 100 Mbps, and 1000 Mbps, 
as well as rates beyond 1000 Mbps if required. 

•

 

Increased availability 

If a link within a LAG fails or is replaced, the traffic is not disrupted and 
communication is maintained (even though the available capacity is reduced). 

•

 

Load sharing

 

Traffic is distributed across multiple links, minimizing the probability that a 
single link be overwhelmed. 

•

 

Use of existing hardware

 

Software replaces the need to upgrade the hardware to higher bandwidth 
capacity. 

 
The Link Aggregation Control Protocol (LACP) 

LACP, specified in the IEEE standard 802.3ad, provides a standardized means for 
dynamically exchanging information between two switches in order to configure and maintain 
link aggregation groups automatically. LACP can automatically detect the presence of other 
aggregation-capable network devices in the system. It enables you to determine which links in 
a system can be aggregated. For each aggregatable link, the switches exchange LACP frames 
in order to allocate the link to a Link Aggregation Group. 

LACP Modes 

The LACP interface supports two modes of operation, as follows: 

Содержание ESB26






































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESB26

D-Link DI-106 Series Faq preview
DI-106 Series
Бренд: D-Link Страницы: 29
D-Link DGS-3700 Series User Manual preview
DGS-3700 Series
Бренд: D-Link Страницы: 292
D-Link DGS-3224SR User Manual preview
DGS-3224SR
Бренд: D-Link Страницы: 140
D-Link DGS-1224T - Web Smart Switch User Manual preview
DGS-1224T - Web Smart Switch
Бренд: D-Link Страницы: 61
D-Link DI-LB604 - Load Balancing Router Quick Installation Manual preview
DI-LB604 - Load Balancing Router
Бренд: D-Link Страницы: 14
D-Link DIR-605L Specification preview
DIR-605L
Бренд: D-Link Страницы: 2
D-Link DIR-510L Manual preview
DIR-510L
Бренд: D-Link Страницы: 45
D-Link DES-3550 Manual preview
DES-3550
Бренд: D-Link Страницы: 218
D-Link DES-3528 - xStack Switch - Stackable User Manual preview
DES-3528 - xStack Switch - Stackable
Бренд: D-Link Страницы: 322
D-Link DIR-130 - Broadband VPN Router How To Set Up preview
DIR-130 - Broadband VPN Router
Бренд: D-Link Страницы: 10
D-Link DIR-130 - Broadband VPN Router Troubleshooting Manual preview
DIR-130 - Broadband VPN Router
Бренд: D-Link Страницы: 4
D-Link DIR-130 - Broadband VPN Router Configuration preview
DIR-130 - Broadband VPN Router
Бренд: D-Link Страницы: 13
D-Link DIR Series Configuration Manual preview
DIR Series
Бренд: D-Link Страницы: 13
D-Link DI-804HV - Express ENwork Router Configuration Manual preview
DI-804HV - Express ENwork Router
Бренд: D-Link Страницы: 19
D-Link DI-808HV Quick Installation Manual preview
DI-808HV
Бренд: D-Link Страницы: 12
D-Link DI-804 Quick Install Manual preview
DI-804
Бренд: D-Link Страницы: 8
D-Link DI-604UP Quick Install Manual preview
DI-604UP
Бренд: D-Link Страницы: 16
D-Link DI-304 Technical Bulletin preview
DI-304
Бренд: D-Link Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды