Nokia ESB26 Скачать руководство пользователя страница 353 | Manualshive

Страница: 353 / 421

background image

MN700004 Rev 01

342

31. NTP Client Description

Introduction

NTP (Network Time Protocol) is a protocol built on top of TCP/IP that assures accurate local
timekeeping with reference to radio, atomic or other clocks located on the Internet. This
protocol is capable of synchronizing distributed clocks within milliseconds over long periods.
It is defined in STD 12, RFC 1119 (definition from The Free On-line Dictionary of
Computing, http://wombat.doc.ic.ac.uk/).

BiNOS’s NTP Client supports all features described in RFC-1059 (Version 1), RFC-1119
(Version 2) and RFC-1305 (Version 3), except for the DES and RSA authentication
mechanism. Support of these RFCs means that the NTP Client can synchronize its local clock
with NTP servers that support any of these documents. The maximal number of remote NTP
servers is restricted to 5. (BiNOS also supports the “Daytime” and “Time” remote
synchronization protocols defined in RFC867 and RFC868 respectively. These protocols
synchronize with only one server -- see the description of the

time-server

command in "The

NTP Timeserver Commands").

NTP has become a standard for Internet time synchronization. Most importantly, there are
more than 100000 free NTP timeservers in the world. Using the NTP protocol, the Nokia
ESB26 switch time can be synchronized by the network administrator almost anywhere in the
world with a minimal effort. Because of its mode of operation (a complicated election
algorithm and MD5 authentication) and the Nokia ESB26 switch capabilities, the NTP Client
is immune to almost any kind of network attack. Furthermore, the NTP Client guarantees high
precision time synchronization.

In brief, the NTP Client features are:

•

Ability to synchronize with RFC-1059 (Version 1), RFC-1119 (Version 2) or
RFC-1305(Version 3) compatible NTP Servers;

•

MD5 authentication algorithm;

•

Up to 5 remote NTP timeservers for polling.

NOTE

Because of some newly introduced features in the time synchronization of the Nokia ESB26
switch, commands for setting time synchronization differ slightly from commands in older
versions of BiNOS. Measures have been taken to preserve compatibility with older versions.
The new version supports old style commands in order to permit execution of previously
saved configurations.

However, it is strongly recommended NOT to use old style commands in the new version.

The NTP Timeserver Commands

Table 31-1 summarizes the NTP timeserver commands.

«
...
351
352
353
354
355
...
»

Содержание ESB26






































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ESB26

VigorIPPBX 2820 Series

Бренд: Draytek Страницы: 29

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

Бренд: Watchguard Страницы: 30

SmartMesh IA-510 D2511

Бренд: Dust Networks Страницы: 30

Бренд: Draytek Страницы: 2

Бренд: Genie Страницы: 6

Бренд: axing Страницы: 52

Media Board D/120JCT-LS-EW

Бренд: Dialogic Страницы: 2

SinoCon C2000-C2-SHK0401-BB1

Бренд: KonNad Страницы: 12

Бренд: CalAmp Страницы: 115

Бренд: VideoWave Страницы: 12

Бренд: TP-Link Страницы: 16

Бренд: Planet Страницы: 54

NVR2104/2108HS-W-4KS2 1U

Бренд: Dahua Technology Страницы: 363

Бренд: Hi-flying Страницы: 59

TeraBridge 5845

Бренд: Proxim Страницы: 4

Бренд: Xtatix Страницы: 12

Бренд: bintec elmeg Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды