Nokia 603 Скачать руководство пользователя страница 93

Страница: 93 / 226

Symptom

Problem

Repair solution

Able to switch on Bluetooth on

phone user interface, but unable

to detect other Bluetooth devices

Open circuit solder joints or

detached component in

Bluetooth antenna circuit

Repair of Bluetooth antenna

circuit

Problems connecting to specific

manufacturer/model Bluetooth

accessory (specific Bluetooth

profile supported by phone and

accessory in product

specification)

Possible interoperability issue

with accessory fixed in recent

Nokia phone software release

(check Nokia Service Bulletin for

the latest information)

Update phone software to

the latest version if advised

in Nokia Service Bulletin

Note:

The phone

Bluetooth Address and

software version are

displayed by pressing

*#2820# when Bluetooth

is on.

Able to turn on FM radio and

Bluetooth on phone user

interface, but unable to detect

local FM radio stations with FM

headset inserted

Open circuit solder joints or

detached component in FM

antenna circuit

Repair of FM receiver antenna

circuit

Able to perform scans to detect

local FM radio stations with

functional FM headset inserted,

but unable to hear FM audio

through headset

Open circuit solder joints or

detached component in FM

receiver audio path between

Bluetooth/FM ASIC and headset

Repair of FM audio circuit

Users may experience the following problems resulting in functional phones being returned to the repair

centre:

Symptom

Problem

Repair solution

Bluetooth feature does not

operate as desired with another

Bluetooth device

Bluetooth Profile implemented

in Bluetooth accessory not

supported in Nokia phone

Use Bluetooth accessory with

Bluetooth profiles supported

by phone

Poor FM radio reception (unable

to detect many radio stations)

Nokia headset not being used

Use Nokia headset

BT and FM radio test coverage

The tests listed in the table below should be performed to verify whether the Bluetooth and FM receiver are

functional. The use of self tests is described in section

Bluetooth and FM radio self tests in Phoenix

Test

Test Coverage

Repair solution

Bluetooth Self Test: ST_BT_IF_TEST

Bluetooth-FM ASIC UART interface

(controls Bluetooth and FM

receiver)

Replacement of BOB module

(or repair of phone BB)

Bluetooth Self Test:

ST_BT_WAKEUP_TEST

Bluetooth ASIC interrupt control

interface

Replacement of BOB module

(or repair of phone BB)

Bluetooth Self Test:

ST_BT_AUDIO_IF_TEST

Bluetooth ASIC PCM interface

Replacement of BOB module

(or repair of phone BB)

RM-779

BB Troubleshooting and Manual Tuning Guide

Issue 1

COMPANY CONFIDENTIAL

Page 3 – 45

Содержание 603











































































































































































Результаты поиска

Содержание 603

Отзывы:

Бренды по названию

Популярные бренды

Nokia 603, Руководство по обслуживанию

Результаты поиска

Содержание 603

Отзывы:

Бренды по названию

Популярные бренды