NKT Photonics Koheras ADJUSTIK HP Скачать руководство пользователя страница 93

Страница: 93 / 115

Connecting power

Procedure 6

Connecting the door interlock circuit

Bus defeater

A bus defeater must be placed on the last device in the External bus chain

topology. In

Figure 59

the bus defeater is placed on the bus output connector of

a connected accessory.

The External bus includes an extension of the interlock circuit. The defeater plug

loops the circuit at the last External bus connector in the system with no other

devices attached to the bus chain. If no defeater is used, the interlock circuit will

be open and disable the laser in the chassis in the same manner as the door

switch opening. The defeater is included with the laser, it is a standard male DB-

15 connector with the necessary pins looped back – see

Table 12 on page 79

Connecting power

Power is supplied to the laser through the rear AC input connector. The

connector is a standard C-14 type designed for use with an AC power cord that is

fitted with a C-13 connector. Electrical and cable specifications are listed in

Table 10

Table 10

Power specifications

Action

Install a switch that opens when the door accessing the laser installation enclosure is

opened. The switch must comply with safety regulations.

2 Using a cable with a maximum wire length of five meters and at a minimum 26 AWG,

connect the switch to a LEMO connector. For cable lengths longer than five meters, it is

recommended to use shielded cable.

3 Perform a continuity test using a multimeter:

•

First connect the multimeter leads to the interlock plug terminals.

•

Confirm when the enclosure door is closed, the meter shows the circuit as closed.

•

Confirm when the enclosure door opens, the meter shows the circuit as open.

4 Insert the LEMO connector into the LEMO interlock connector on the rear panel of the laser.

Item

Description

AC Mains

Input

100-240 VAC @ 50-60 Hz

Power cord

The power cord must be capable to safely transmit the laser’s specified AC

ratings while maintaining a safe connection with the local AC mains outlets.

The power cord used must follow local or national regulations.

AC connector

(inlet)

IEC 60320 – C14

Power cord

connector

The power cord must have an IEC 60320 C-13 connector.

Содержание Koheras ADJUSTIK HP




















































































































Результаты поиска

Содержание Koheras ADJUSTIK HP

Отзывы:

Похожие инструкции для Koheras ADJUSTIK HP

Бренды по названию

Популярные бренды

NKT Photonics Koheras ADJUSTIK HP, Руководство по эксплуатации продукта

Результаты поиска

Содержание Koheras ADJUSTIK HP

Отзывы:

Похожие инструкции для Koheras ADJUSTIK HP

Бренды по названию

Популярные бренды