NKT Photonics Koheras ADJUSTIK HP Скачать руководство пользователя страница 76

Страница: 76 / 115

CONTROL settings

coupling. Refer to

“Wavelength modulation coupling” on page 42

for further

information.

Note:

When using wavelength modulation with an X15 laser, and the Modulation

range parameter is set to

Narrow

, the modulation signal will be AC-coupled, and

the DC-component enters a software integrating function that tunes the wave

length up or down when the DC-voltage varies either positive or negative re

spectively. The speed of wavelength tuning is set with the Integrating update

interval.

Modulation

Range

For X15 lasers, you can use the Modulation

Range

drop-down menu to set the

modulation range to either narrow or wide.

When set to

Narrow

, modulation depth is limited but the X15’s low phase noise is

maintained. To increase the modulation depth, change the range setting to

Wide

When the modulation range is set to

Wide

, phase noise increases.

Note:

Refer to

“Narrow vs. Wide modulation range” on page 42

for further infor

mation on configuring the modulation range.

Signal output

You can output the internal generator signal (internal modulation) from the

wavelength modulation pins of the laser. To output the signal from the pins, set

the Modulation type to

Internal

and the

Signal

output

selector to

Enabled

. To

disable the output signal, set the

Signal

output

drop-down menu to

Disabled

When multiple lasers are used, one laser can be used as a master signal

generator with the other lasers configured as slaves.

1. For all the lasers, connect the

Wav

pins together and the

Wavelength-

pins together.

2. Designate one laser as the master by setting it to operate in

Internal

modulation mode with the

Signal

output

setting

Enabled

3. All other lasers will operate in slave mode by setting them to operate in

External

modulation mode.

Integrating update interval

You can set the update interval of the software integration function with this

setting. The setting is intended for use with X15 lasers when they are set to

coupling and

Narrow

modulation range.

Internal generator

Frequency

When the modulation source is set to

Internal

, the frequency of the internal

generator signal can be adjusted to between 8 MHz (0.008 Hz) and 100 kHz

(100,000 Hz). To adjust the frequency, use either the slider or the direct input

field in the upper right corner of the slider.

Содержание Koheras ADJUSTIK HP




















































































































Результаты поиска

Содержание Koheras ADJUSTIK HP

Отзывы:

Похожие инструкции для Koheras ADJUSTIK HP

Бренды по названию

Популярные бренды

NKT Photonics Koheras ADJUSTIK HP, Руководство по эксплуатации продукта

Результаты поиска

Содержание Koheras ADJUSTIK HP

Отзывы:

Похожие инструкции для Koheras ADJUSTIK HP

Бренды по названию

Популярные бренды