What to do if...
(troubleshooting guide)
q
Powering an electrical phase, the motor does not move:
After excluding the possibility that thermal protection is active, in which case it is
sufficient to wait for the motor to cool down, make sure the mains voltage cor-
responds to the values indicated in the technical characteristics of this manual
by measuring the electricity between the “common” wire and the electrical phase
wire supplied with current. Finally, try to supply the opposite electrical phase.
q
When sending a Raise command, the motor does not start:
This can happen if the roller shutter is near the Upper limit switch (“0”). In this
case you must lower the roller shutter a little bit and give the Raise command
again.
q
The system operates in the emergency condition with an operator pre-
sent:
– Check to see if the motor has undergone a significant thermal or mechanical
shock.
– Make sure each part of the motor is still in good condition.
– Perform the deletion procedure (procedure
B.11, A.10
or
C.4
) and adjust the
limit switches again.
Disposal of the product
As in installation operations, disposal operations must be performed by qualified
personnel at the end of the product’s lifespan.
The product is made of various types of materials: some of them may be recycled,
while others must be scrapped. Find out about recycling and disposal systems in
use in your area for this product category.
Warning!
– Some parts of the product may contain polluting or hazardous sub-
stances which, if released to the environment, may cause serious damage to the
environment or to human health.
As indicated by the symbol appearing here, the product may not be
disposed of with other household wastes. Separate the waste into cat-
egories for disposal, according to the methods established by current
legislation in your area, or return the product to the retailer when pur-
chasing a new version.
Warning!
– Local legislation may impose heavy fines in the event of legal disposal
of this product.
The product’s packaging materials must be disposed of in full compliance with local
regulations.
Technical Characteristics
■
Frequency
433.92 MHz
■
Power emitted:
0 dBm
■
Radio coding:
“BD”.
Refer to the technical characteristics stated on the motor’s nameplate.
Note
: • All technical specifications stated herein refer to an ambient temperature of
20° C (± 5° C). • Nice S.p.A. reserves the right to apply modifications to products
at any time when deemed necessary, maintaining the same intended use and func-
tionality.
Simplified EU declaration of conformity
Hereby, NICE S.p.A., declares that the radio equipment type NX SOL MA 615 SH
BD, NX SOL MA 1014 SH BD and NX SOL MA 2010 SH BD, is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address: https://www.niceforyou.com/en/support.
COMPLIANCE WITH THE FCC RULES (PART 15) AND RSS-210 RULES
This device complies with Industry Canada’s licence-exempt RSS-210s, and with
Part 15 of the FCC rules of the United States of America. Operation is subject to
the following two conditions: (1) this device may not cause interference; (2) this de-
vice must accept any interference, including interference that may cause undesired
operation of the device. Any changes or modifications made to this device, without
the express permission of the manufacturer, may void the user’s authority to operate
this device.
5
0
10
15
20
25
35
40
30
45
Km/h
“
0
”
instantaneous
wind speed
gust of wind
automatic
operation
manual
operation
momentary drops in
speed, within the
hysteresis values
hysteresis threshold:
positioned automatically
at half the set threshold
value
drops in speed lasting
less than 10 minutes
set threshold
value: e.g.
30Klux
over-threshold
hysteresis
under-threshold
active manual
commands
active manual
commands
manual commands
deactivated
protection deactivated
protection deactivated
after 3 seconds
after about 10 minutes
after 1 or 4 minutes
system active
8
37
– English
