A.7 - Memorising ANOTHER TRANSMITTER (second, third, etc.)
BiDi
NOTES AND WARNINGS
• The motor configured to operate in TWO-WAY mode can memorise up to 16 transmitters.
• To run procedures A.7 you must have a
new transmitter
to memorise and an
old
previously memorised transmitter. The two transmitters must have the “PRG” and
“ESC” buttons (like “ERA P” and “ERA W” transmitters).
• Procedures A.7 memorise all the
new
transmitter’s buttons in “Mode I”, with the same configuration as the
old
transmitter (for details about “Mode I” see par. 4.6.1).
1
2
3
OLD
PRG
(x
1
)
2
NEW
=
5
sec
2
On the OLD transmitter:
Press
and release the button (1 time);
count 2 movements;
On the NEW transmitter:
hold
down the button and
release it after
5
seconds
;
count 2 movements;
3
4
end
OLD
PRG
(x
1
)
2
NEW
(x
1
)
3
On the OLD transmitter:
Press
and release the button (1 time);
count 2 movements;
On the NEW transmitter:
Press
and release the button (1 time);
count
3 movements
(= transmitter
memorised)
.
A
A.6 - Programming an INTERMEDIATE POSITION (position “H”)
BiDi
NOTES AND WARNINGS
•
This procedure memorises an intermediate position (position “H”) between the Up (“0”) and Down (“1”) limit switch positions. When the automation is being used,
after giving the
intermediate position
command, the system will automatically stop the roller shutter at the programmed “H” position.
• Up to 30 “H” positions can be memorised if the motor is configured to operate in ONE-WAY mode, or up to 6 “H” positions if the motor is configured to operate in
TWO-WAY mode, in any desired position, provided that they are within the space delimited by the two limit switches. These positions can only be programmed after
the limit switch positions. Repeat this procedure for each position you wish to memorise.
• The first “H” position must be programmed using the buttons
▲
+
▼
,
on the transmitter used to run the procedure itself
. However, each subsequent position
“H” must be programmed using a button
on another non-memorised transmitter
.
• To change an existing “H” position, move the awning to the desired height and run this procedure; in
step 06
, however, press the button associated with the exist-
ing “H” position you are changing.
1
2
3
4
“
H
”
(x
1
)
PRG
2
=
5
sec
2
Move the roller shutter to
the desired “
H
” position.
Press and release
the button (
1 time
);
count 2 movements.
Hold down both buttons...
release them after
5 sec-
onds
;
count 2 movements.
4
5
6
...
Precisely ad-
justing the
“H” posi-
tion
“
H
”
=
5
sec
3
Select one of the following potions
and execute it:
• option A
– to memorise the
FIRST “H” position.
• option B
– to memorise a SUP-
PLEMENTARY “H” position.
Press the buttons until you reach the desired position.
Hold down the but-
ton and
release it after
5 sec-
onds
;
count 3 movements.
option –
A
6
end
option –
B
6
end
=
5
sec
4
=
5
sec
...
...
4
Hold down both but-
tons...
release them
after
5 sec-
onds
;
count 4 movements.
On ANOTHER transmitter,
which has NOT been memo-
rised:
hold down any button
you wish;
release it after
5 seconds
;
count 4 movements.
B
A
11
– English
