Nice hyke HK7024, Инструкции и предупреждения по установке и использованию

Страница: 25 / 120

EN
English –
13
TECHNICAL SPECIFICATIONS OF PRODUCT
WARNINGS: •
All technical specifications stated in this section refer to an ambient temperature of 20°C (± 5°C). • Nice S.p.a. reserves the right to apply modifica-
tions to products at any time when deemed necessary, maintaining the same intended use and functionality.
HK7024K HK7024KHS HK7224K HK7224KHS
Type
Electromechanical gearmotor for automations of gates and
automatic doors with DC motor, epicyclical gear reducer and
mechanical release. Built-in control unit and OXI radio receiver. Electromechanical gearmotor for automations of gates
and automatic doors with DC motor, epicyclical gear
reducer and mechanical release.
Maximum torque 500 Nm
Nominal torque
120 Nm
Speed under no load 1.5 RPM 2 RPM 1.5 RPM 2 RPM
Maximum cycle frequency 40 cycles/hour
Maximum continuous cycle time approx. 7 minutes
Application limits the product can be used on
gates with leaf weights up
to 330 kg or with lengths
up to 3.5 m the product can be used on
gates with leaf weights up
to 270 kg or with lengths
up to 3 m the product can be used on
gates with leaf weights up
to 330 kg or with lengths
up to 3.5 m the product can be used on
gates with leaf weights up
to 270 kg or with lengths
up to 3 m
Lifetime
estimated between 150,000 cycles and 500,000 cycles, according to the conditions stated in table 13 and graph 3
Power supply 230 Vac ±10%; 50/60 Hz 24 Vdc (±10%)
Backup power supply provision for buffer battery PS124
Solar power provision for SYKCE kit
Maximum absorbed power 300 W 140 W
Maximum absorbed current
1,5 A (3 A for version
HK7024K/V1
) 6 A for a maximum interval of 2 s
Absorbed power with “All –
Standby” function when powered
by PS124 or SYKCE kit (including
OXI receiver)
less than 100 mW
Flashing light output [*] one LUCYB flashing light (12 V, 21 W bulb)
Electric lock output [*] one 12 Vac electric lock (max 15 VA)
Gate open indicator output [*] one 24 V lamp (max. 4 W) (the output voltage may vary betwe-
en -30 and +50%, the output can also control small relays)
BLUEBUS output one output with load of maximum 15 Bluebus units (max.
6 pairs of MOFB or MOFOB photocells plus 2 pairs of
MOFB or MOFOB photocells routed as opening devices
plus max. 4 MOMB or MOTB control devices)
STOP input for normally closed contacts, normally open contacts or
contacts with constant 8,2 k
Ω
resistance; selection of the
type of contact is in self-learning mode and a modifica-
tion with respect to the memorised status will generate
a “STOP”
SS input for normally open contacts (closure of the contact genera-
tes a Step Step command)
Radio engage SM connector for receivers in the families SMXI, OXI and
OXIFM
Radio AERIAL input 50
Ω
for cable type RG58 or similar
Programmable functions 8 ON-OFF type functions (Table 3) and 8 settable fun-
ctions (Table 5)
Functions in self-learning • Self-learning of devices connected to the BlueBus
output. • Self-learning of the type of device connected to
the “STOP” terminal (NO, NC contact or 8,2 k
Ω
resistan-
ce). • Self-learning of the gate leaf travel and automatic
calculation of deceleration points and partial opening. •
Self-learning of operation with one or two motors
Assembly Vertical, with dedicated fixing plate
Operating temperature
from -20°C to +50°C (at low temperatures, gearmotor efficiency is reduced)
Se in acid, saline or potentially
explosive atmospheres
NO
Protection rating IP 54 (with container intact)
Dimensions (mm)
210 x 290 x 320 h
Weight (kg) 10.5 9.5
[*] - The outputs Flashing Light, Electric lock and Gate Open Indicator can be programmed with other functions (see “TABLE 3 – Level 1 functions”; or via the Oview programmer; see
chapter 8.3). The electrical specifications of the output are adapted to the type of selected function: • flashing light function: lamp 12 Vdc, max. 21 W; • electric lock function: 12 Vac
max. 15 VA; • other outputs (all types): 1 lamp or relay 24Vdc (-30 to +50%), max. 4 W.