Nice hyke HK7024, Инструкции и предупреждения по установке и использованию

Страница: 20 / 120

EN
8
– English
6.2 - Level two programming (adjustable parameters)
All level 2 functions are set by default as highlighted in
grey
in
Table 5
, and may
be modified at any time as explained in
Table 6
.
The parameters can be set on a scale from 1 to 8. To check the value corre-
sponding to each LED see Table 8 . IMPORTANT – In the programming proce-
dure, the maximum time interval that can elapse between activation of one key
and the next is 10 seconds. When this time elapses, the procedure terminates
automatically, memorising the modifications made up until then.o.
TABLE 5 - Second level functions
Input LED Parameter LED (level) Value Description
L1 Pause time L1
L2
L3
L4
L5
L6
L7
L8 5 seconds
15 seconds
30 seconds
45 seconds
60 seconds
80 seconds
120 seconds
180 seconds Sets the pause time, namely
the time which lapses before
automatic closure. This will only
take effect if closing is active.
L2 Step by step function L1 Open – stop – close – stop Sets the sequence of com-
mands associated with the
“Step-by-Step”, “Open” or
“Close” inputs or the radio con-
trol.
Note – When setting L4 , L5 ,
L7 and L8 , the behaviour of
the “Open” and “Close” com-
mands is also modified.
L2 Open – stop – close – open
L3 Open – close – open – close
L4 Apartment block:
• In the opening manoeuvre the “Step by Step” and “Open”
commands have no effect; the “Close” command causes the
movement to be inverted, i.e. the closure of the leaf.
• In the closure manoeuvre the “Step by Step” and “Open”
commands cause the movement to be inverted, i.e. the leaf
to open; the “Close” command has no effect.
L5 Apartment block 2:
• In the opening manoeuvre the “Step by Step” and “Open”
commands have no effect; the “Close” command causes the
movement to be inverted, i.e. the closure of the leaf. If the
transmitted command persists for more than 2 sec-
onds, a “Stop” is performed.
• In the closure manoeuvre the “Step by Step” and “Open”
commands cause the movement to be inverted, i.e. the leaf
to open; the “Close” command has no effect.
If the trans-
mitted command persists for more than 2 seconds, a
“Stop” is performed.
L6 Step-by-step 2 (less than 2 sec. generates partial opening).
L7 Hold-to-run: the manoeuvre is performed only if the transmit-
ted command persists; if the command is interrupted the
manoeuvre stops.
L8 Opening in semi-automatic mode, closing in hold-to-run
mode.
L3 Motor speed L1
L2
L3
L4
L5
L6
L7
L8 Very slow
Slow
Medium
Fast
Very fast
Extremely fast
Fast opening, Slow Closing
Extremely fast Opening, Medium Closing Sets the motor speed during
normal travel.
L4 Motor discharge after
closing
L1
L2
L3
L4
L5
L6
L7
L8 No discharge
Level 1 - Minimum discharge (about 100 ms)
Level 2 - ...
Level 3 - ...
Level 4 - ...
Level 5 - ...
Level 6 - ...
Level 7 - Maximum discharge (about 800 ms) Sets duration of “short inver-
sion” of both motors after per-
forming a Closing manoeuvre
with the aim of reducing the
final residual thrust, guaran-
teeing adequate closure and
facilitating manual release of the
gearmotor.
L5 Motor force
L1
L2
L3
L4
L5
L6
L7
L8 Level 1 - Minimum Force
Level 2 - ...
Level 3 - ...
Level 4 - ...
Level 5 - ...
Level 6 - ...
Level 7 - ...
Level 8 - Maximum Force Adjusts the force of both mo-
tors
L6 Pedestrian or partial opening L1
L2
L3
L4
L5
L6
L7
L8 Pedestrian 1 (opening of leaf M2 to 1/4 of total opening)
Pedestrian 1 (opening of leaf M2 to 1/2 of total opening)
Pedestrian 3 (opening of leaf M2 to 3/4 of total opening)
Pedestrian 4 (Complete opening of leaf 2)
Partial 1 (opening of two leafs to 1/4 of “minimum” opening)
Partial 2 (opening of two leafs to 1/2 of “minimum” opening)
Partial 3 (opening of two leafs to 3/4 of “minimum” opening)
Partial 4 (opening of two leafs to “minimum” opening) Sets type of opening associa-
ted with “Partial open 1” com-
mand.
In levels L5, L6, L7, L8; “mi-
nimum” opening means the
smaller opening out of M1 and
M2; for example, if M1 opens
to 90° and M2 opens to 110°,
the minimum opening is 90°