Nextron MASTERTRACE страница 78 Скачать руководство пользователя | Manualshive

Страница: 78 / 110

background image

MASTER

TRACE

B.1

Appendix B Display Message

Details - Measured

MESSAGE NO:

M1-01

APPLIES TO:

Interface Module

DEFAULT VALUE: N/A

VALUE RANGE: N/A

DISPLAY MODE: All

RESTRICTIONS: None

This message displays the name of the sub-menu when entered.

MESSAGE NO:

M1-02

APPLIES TO:

Interface Module

DEFAULT VALUE:Selected Htr

VALUE RANGE: Set by MODULE RANGE

function

DISPLAY MODE: All

RESTRICTIONS: None

This function selects the heater circuit. Each heater circuit has a unique two-part
Heater Number. The first part is the Module Number and the second part is the
heater circuit within the Control Module. Press [VALUE

ñ

] or [VALUE

ò

] and

then press [STORE] to select a heater circuit. For convenience and to reduce
human error, the Heater Name is also displayed.

MESSAGE NO:

M1-03

APPLIES TO:

Selected Heater

DEFAULT VALUE: N/A

VALUE RANGE: on, off, man on,

no: 1 to 9 alarms

DISPLAY MODE: All

RESTRICTIONS: None

The displayed value is the status of the selected heater. It indicates whether the
heater circuit is on or off and the number of alarm messages associated with the
circuit. The heater circuit is in manual override if “man on”is displayed. See
MANUAL HEATER function.

MESSAGE NO:

M1-04

APPLIES TO:

Selected Heater

DEFAULT VALUE: N/A

VALUE RANGE:

-50 to 500 °C
-58 to 932 °F

DISPLAY MODE: All

RESTRICTIONS: None

For single-RTD modules, the displayed value is the actual measured temperature
of the RTD sensor for this heater circuit. For dual-RTD modules, the displayed
value is calculated from the actual measured temperatures of both RTD sensors
based on the RTD MODE function. The heater circuit is controlled by comparing
the Heater Control Temperature to the Heater Setpoint. If the temperature is
outside the value range then “RTD OPEN” or “RTD SHORT” is displayed.

MESSAGE NO:

M1-05

APPLIES TO:

Selected Heater

DEFAULT VALUE: N/A

VALUE RANGE:

-50 to 500 °C
-58 to 932 °F

DISPLAY MODE: All

RESTRICTIONS: Dual RTD Modules Only

The displayed value is the actual measured temperature of RTD-A sensor for this
heater circuit. It is used to calculate the Heater Control Temperature based on the
RTD MODE function. If the temperature is outside the value range then “RTD
OPEN” or “RTD SHORT” is displayed.

Appendix B Display Message Detail - Measured

Measured Values: Operating Values

MEASURED VALUES:

OPERATING VALUES

SELECT HT: 1-1

?

NONAME

&

HEATER IS on

&

&

no ALARMS

HEATER CONTROL

TEMP: 6°C

&

RTD-A ACTUAL

TEMP: 6°C

&

«
...
76
77
78
79
80
...
»

Содержание MASTERTRACE















































































































Отзывы:

Нет отзывов

Похожие инструкции для MASTERTRACE

Бренд: wattio Страницы: 20

Бренд: Babybee Страницы: 28

Бренд: Parasound Страницы: 72

Бренд: Jafar Страницы: 15

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Minas A4 Series

Бренд: Panasonic Страницы: 5

Бренд: GBD Страницы: 68

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: FAAC Страницы: 32

Бренд: Samson Страницы: 40

Бренд: Maclaren Страницы: 43

Бренд: Lawler Страницы: 5

Бренд: SYR Страницы: 2

PetroVend PV200

Бренд: OPW Страницы: 2

Бренд: DeLaval Страницы: 102

Бренд: Cardin Elettronica Страницы: 56

Бренд: Rain Bird Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды