Nextron MASTERTRACE страница 69 Скачать руководство пользователя | Manualshive

Страница: 69 / 110

background image

MASTER

TRACE

A.9

Appendix A Display Message

Details - Setpoints

MESSAGE NO:

S3-03

APPLIES TO:

Interface Module

DEFAULT VALUE: 1-30

VALUE RANGE: 1-30, 31-60, … , 211-240,

241-254

DISPLAY MODE: Advanced

RESTRICTIONS: MR100 Interface

This function selects the range of Control Module numbers connected to this
Interface Module. All Control Modules connected to this Interface Module must
be within this range.

MESSAGE NO:

S3-04

APPLIES TO:

Interface Module

DEFAULT VALUE: advanced user VALUE RANGE: advanced user, normal user
DISPLAY MODE: All

RESTRICTIONS: None

This function determines what messages are displayed. If set to “advanced user”,
all messages are displayed. If set to “normal user”, only the basic messages are
displayed. Each message listed in this appendix shows the Display Mode required
to see the message. “Advanced” indicates that the display mode must be set to
“advanced user” to view the message.

MESSAGE NO:

S3-05

APPLIES TO:

Interface Module

DEFAULT VALUE: System status VALUE RANGE: See values below
DISPLAY MODE: Advanced

RESTRICTIONS: None

This function specifies the information that will be displayed when no key has
been pressed for the Display Timeout interval as described below.
VALUE

INFORMATION DISPLAYED

System status

Alarm status of all the heaters

Heater status

Heater status of selected heater

Heater temp

Temperature of the selected heater

Scan heater

All measured values of the selected heater

Scan temps

Temperatures of all enabled heaters

Scan currents

Phase currents of all enabled heaters

Scan gnd faults

Ground fault currents of all enabled heaters

Scan all heaters

All measured values of all enabled heaters

MESSAGE NO:

S3-06

APPLIES TO:

Interface Module

DEFAULT VALUE: 60 seconds

VALUE RANGE: 5 to 600 s, off

DISPLAY MODE: Advanced

RESTRICTIONS: None

This function sets the length of time, from the last key press, to automatically
return to the Default Display information. To disables this function set the value to
“off”.

MESSAGE NO:

S3-07

APPLIES TO:

Interface Module

DEFAULT VALUE: 3 seconds

VALUE RANGE: 1 to 10 seconds

DISPLAY MODE: Advanced

RESTRICTIONS: None

This function sets the length of time between the display of successive messages.
Select a value that is comfortable for the reading speed of the operator.

MESSAGE NO:

S3-08

APPLIES TO:

Interface Module

DEFAULT VALUE: Celsius

VALUE RANGE:

Celsius, Fahrenheit

DISPLAY MODE:

Advanced

RESTRICTIONS: None

This function sets the units of measure for temperature. All temperatures are
displayed in the selected units of either Celsius degrees (C°) or Fahrenheit
degrees (F°).

MODULE RANGE

1-30

?

DISPLAY MODE:

advanced user

?

DEFAULT DISPLAY:

System Status

?

DISPLAY TIMEOUT:

60 seconds

?

SCAN TIME:

2 seconds

?

TEMPERATURE UNITS:

Celcius

?

«
...
67
68
69
70
71
...
»

Содержание MASTERTRACE















































































































Отзывы:

Нет отзывов

Похожие инструкции для MASTERTRACE

Relion 670 series

Бренд: ABB Страницы: 760

Бренд: ABB Страницы: 128

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: Microchip Technology Страницы: 37

Бренд: Fantech Страницы: 2

Бренд: LANGER EMV-Technik Страницы: 48

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 22

FSDrive-MV1000 Series

Бренд: YASKAWA Страницы: 260

Бренд: YASKAWA Страницы: 114

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды