Nextron MASTERTRACE страница 16 Скачать руководство пользователя

Страница: 16 / 110

MASTER

TRACE

3.3

Chapter 3 Product Description

3.3 Control Module Specifications

3.3.1 MS-1DIN2 Control Module

Temperature Input

Range:

-50°C to +500°C

Accuracy:

±2°C

Repeatability:

±1°C

Sensor:

Two 100 ohm, Platinum, 3-wire RTD
per point
20 ohm maximum lead resistance

Heater Switching

Number of Switches:

One dual pole

Switch Rating:

30A @ 280Vac max

Current Measurement:

0.1 to 30A 3%±0.2A

GF Measurement:

10 to 1000mA 5% ±2mA

Voltage Measurement:

0 to 300Vac 3%±2V

Control Power

Power Requirements:

20VA @ 120Vac, 50 or 60Hz

Communications

Communication Ports:

(1) Parallel Local Interface connection
(2) Serial network connections

Serial Communications
Type:

RS485

Protocol:

Modbus® RTU.

Transmission Rate:

600, 1200, 2400, 4800, 9600 baud.

Interconnect:

2-wire, shielded, twisted pair.

Highway Distance:

4,000 feet without repeater.

Modules per Highway:

(1) Interface and (30) Control Modules.

Measured Values

Temperature:

-50 to 500°C (-58 to 932°F)

Minimum Temperature:

-50 to 500°C (-58 to 932°F)

Maximum Temperature: -50 to 500°C (-58 to 932°F)
Heater Current:

0.1 to 100A

Ground Fault Current:

0.01 to 1.0A

Heater Voltage:

0 to 300Vac

Heater Utilization:

0 to 100%

Power Consumption:

0 to 1,000 MWh

Operating Cost:

0 to $1,000,000.00

Environment

Approval:

CSA NRTL/C for Ordinary areas

Operating Range:

-40°C to +60°C

Conformal Coating:

Boards conformal coated for hostile
environments

Alarm

Alarm Output:

Programmable for NO or NC contacts

One DC opto-isolated contact
One dry mechanical contact

Alarm Output Rating:

DC contact: 30Vdc/0.1A, 500mW max
Dry mech contact: [email protected] max

Alarm Light Output:

LED Indicator: 12Vdc/30mA

Alarm Messages
Temperature:

High Temperature Alarm
Low Temperature Alarm

Current:

Low Current Alarm
High Current Trip

Ground Fault Current:

Ground Fault Current Alarm
Ground Fault Current Trip

Voltage:

Low Voltage Alarm

Hardware:

Self-Check Failure
Switch Shorted
RTD Open
RTD Shorted

User-Settable Options

Heater Status:

Enable or Disable

Heater Name or Tag:

16 Character Alphanumeric

Temperature Units:

°C or °F

Control Strategy:

On or Off

Deadband:

0 to 50C° (0-90F°)

Temperature Setpoint:

0 to 500°C (32 to 932°F)

High Temp Alarm:

0 to 500°C (32 to 932°F)

Low Temp Alarm:

-50 to 500°C (-58 to 932°F)

High Current Alarm:

0.5 to 30A

Low Current Alarm:

0.5 to 30A

High Current Trip:

0.5 to 30A

Ground Fault Alarm:

0.01 to 1.0A

Ground Fault Trip:

0.01 to 1.0A

TraceCheck Interval:

1 to 24 hr.

Low Voltage Alarm:

0 to 300Vac

RTD Control Strategy:

Single, Backup, Highest, Lowest,
Average or High Temperature Cutout

RTD Fail-safe:

Heater On or Heater Off

Master Override Input:

On or Off

Alarm Contacts:

NO or NC for each contact

Alarm Light:

Alarm on, Alarm off, Flash during alarm
then on, Flash during alarm then off

Specifications subject to change without notice.

Содержание MASTERTRACE















































































































Результаты поиска

Содержание MASTERTRACE

Отзывы:

Похожие инструкции для MASTERTRACE

Бренды по названию

Популярные бренды

Nextron MASTERTRACE, Руководство по эксплуатации

Результаты поиска

Содержание MASTERTRACE

Отзывы:

Похожие инструкции для MASTERTRACE

Бренды по названию

Популярные бренды