manualshive.com logo in svg

Nextron MASTERTRACE, Руководство по эксплуатации

Nextron MASTERTRACE - Продукт высокой точности для трассировки. Операционное руководство доступно для загрузки бесплатно с {сайта}. Обеспечьте безопасность и эффективность с помощью нашего ручного устройства трассировки. Идеально подходит для профессиональных инженеров и техников.

Поделиться
Скачать
background image

MASTER

TRACE

Contents

1 Overview ..................................................................................................................................... 1.1

1.1 Use of This Manual .............................................................................................................................................. 1.1
1.2 Related Documents ............................................................................................................................................. 1.1
1.3 Conventions ......................................................................................................................................................... 1.1
1.4 Scope ................................................................................................................................................................... 1.1
1.5 Rev.A Enhancements ........................................................................................................................................... 1.1
1.6 Overall Enhancements ........................................................................................................................................ 1.1
1.7 Shipping Content ................................................................................................................................................. 1.1
1.8 Theory of Operation .............................................................................................................................................. 1.2

2 Getting Started ........................................................................................................................... 2.1

2.1 Introduction ........................................................................................................................................................... 2.1
2.2 Enable Heaters .................................................................................................................................................... 2.1
2.3 Enter Setpoints ..................................................................................................................................................... 2.2
2.4 Test Heater & Alarms ........................................................................................................................................... 2.4
2.5 Monitor System Status .......................................................................................................................................... 2.4

3 Product Description ................................................................................................................... 3.1

3.1 Introduction ........................................................................................................................................................... 3.1
3.2 Features and Benefits .......................................................................................................................................... 3.2
3.3 Control Module Specifications ............................................................................................................................. 3.3
3.4 Model Codes for Control Panels ....................................................................................................................... 3.19

4 Installation ................................................................................................................................... 4.1

4.1 Control Panel Mounting ....................................................................................................................................... 4.1
4.2 RTD Sensor Wiring .............................................................................................................................................. 4.1
4.3 Ground Fault Protection ....................................................................................................................................... 4.1
4.4 Ground Fault Testing ............................................................................................................................................ 4.1
4.5 Power and Heater Wiring ..................................................................................................................................... 4.1
4.6 Ground Connection .............................................................................................................................................. 4.1
4.7 Safety Ground ....................................................................................................................................................... 4.2
4.8 Control Power Wiring ........................................................................................................................................... 4.2
4.9 Commissioning ................................................................................................................................................... 4.2

5 Operation ..................................................................................................................................... 5.1

5.1  Control Modules .................................................................................................................................................. 5.1
5.2  Interface Modules - ML100 & MR100 .................................................................................................................. 5.6
5.3  Responding to Alarms ........................................................................................................................................ 5.9
5.4  Setpoint Values Menu: Single-Phase Modules ................................................................................................ 5.10
5.5  Setpoint Values Menu: Three-Phase Modules (1- and 5-point only) ................................................................. 5.11
5.6  Measured Values Menu: Single-Phase Modules ............................................................................................  5.12
5.7  Measured Values Menu: Three-Phase Modules .............................................................................................. 5.13
5.8  Interface Module - MR100 for Windows CE ...................................................................................................... 5.14

6 Programming & Setup ................................................................................................................ 6.1

6.1 Getting Started ...................................................................................................................................................... 6.1
6.2 Program Enable ................................................................................................................................................... 6.1
6.3 Module List/Communication Map ........................................................................................................................ 6.1
6.4 Heater Enable ...................................................................................................................................................... 6.1
6.5 Example: Change the Setpoint for Heater 3-2 to 50°C ....................................................................................... 6.1

7 Networking Modules .................................................................................................................. 7.1

7.1 RS-485 Communications in Modbus RTU ......................................................................................................... 7.1
7.2 RS-485 Wiring ...................................................................................................................................................... 7.1
7.3 Removing a Control Module from the Network ................................................................................................... 7.1
7.4 Adding a Control Module to the Network .............................................................................................................. 7.1
7.5 Communication With Third Party Equipment  ..................................................................................................................7.1
7.6 Baud Rate ............................................................................................................................................................ 7.3
7.7 Ethernet Communication in Modbus TCP and MasterTrace Heat Tracing Panel Option “ETH” ........................ 7.3

Содержание MASTERTRACE















































































































Отзывы:

Нет отзывов

Похожие инструкции для MASTERTRACE

Salda FLEX Service Manual preview
FLEX
Бренд: Salda Страницы: 20
Safran MorphoAccess SIGMA Extreme Series Installation Manual preview
MorphoAccess SIGMA Extreme Series
Бренд: Safran Страницы: 79
Lawler 805 Installation & Maintenance Manual preview
805
Бренд: Lawler Страницы: 5
IDTECK iTDC Troubleshooting Manual preview
iTDC
Бренд: IDTECK Страницы: 94
Parkside PDWE 8 A2 Operation And Safety Notes Translation Of The Original Instructions preview
PDWE 8 A2
Бренд: Parkside Страницы: 65
Zamel P-258/2 Instructions Manual preview
P-258/2
Бренд: Zamel Страницы: 23
Zamel P-256/8 Manual Instruction preview
P-256/8
Бренд: Zamel Страницы: 2
Zamel supla SRW-01 Quick Start Manual preview
supla SRW-01
Бренд: Zamel Страницы: 2
Zander Aachen SCB Series Operating Instructions Manual preview
SCB Series
Бренд: Zander Aachen Страницы: 44
Zamel Extra Free ROB-01/12-24V Manual Instruction preview
Extra Free ROB-01/12-24V
Бренд: Zamel Страницы: 2
Zamel ROW-01 Instruction Manual preview
ROW-01
Бренд: Zamel Страницы: 14
Hunter 99112 Installation preview
99112
Бренд: Hunter Страницы: 2
Tektronix 73A-541 User Manual preview
73A-541
Бренд: Tektronix Страницы: 112
TeleMann DTR5000N Manual preview
DTR5000N
Бренд: TeleMann Страницы: 4
Gemini GTL5W Instruction Manual preview
GTL5W
Бренд: Gemini Страницы: 9
M-system R7EWTU Instruction Manual preview
R7EWTU
Бренд: M-system Страницы: 18
asalvo TRIO ROMA Instruction Manual For Use preview
TRIO ROMA
Бренд: asalvo Страницы: 46
Dickey-John Control Point Operator'S Manual preview
Control Point
Бренд: Dickey-John Страницы: 109

Бренды по названию

Популярные бренды

Загрузить еще бренды