manualshive.com logo in svg

Nextron MASTERTRACE, Руководство по эксплуатации

Nextron MASTERTRACE - Продукт высокой точности для трассировки. Операционное руководство доступно для загрузки бесплатно с {сайта}. Обеспечьте безопасность и эффективность с помощью нашего ручного устройства трассировки. Идеально подходит для профессиональных инженеров и техников.

Поделиться
Скачать
background image

MASTER

TRACE

A.11

Appendix A Display Message

Details - Setpoints

measurement from the RTD Sampler is transmitted to the control module via either
RS485 cable or RF Modem.
If the option “RTD Transmitter” is selected, the control module uses the temperature
measurement signal transmitted from the RTD Transmitters to control heaters. The
RTD Transmitter is another independent temperature-measurement device. The ac-
tual RTD sensor is to be locally wired to the RTD Transmitter. Since the transmitter
uses just two 18AWG wires to transmit its temperature measurement to the control
module in a form of 4-20mA dc current, it can be located up to 7km away from the
control module. This creates a great deal of flexibility to the RTD wiring process.
Each control point requires a dedicated RTD Transmitter for its temperature meas-
urement. Refer to Appendix F for the operation details of RTD Sampler and RTD
Transmitter.

MESSAGE NO:

S3-15

APPLIES TO:

Interface Module

DEFAULT VALUE: 1200

VALUE RANGE:

600,1200,2400,4800,9600

DISPLAY MODE:

Advanced

RESTRICTIONS: MR100 Interface Module

This function sets the communication baud rate for the MR100 serial port .

MESSAGE NO:

S3-16

APPLIES TO:

Interface Module

DEFAULT VALUE: 1200

VALUE RANGE:

600,1200,2400,4800,9600

DISPLAY MODE:

Advanced

RESTRICTIONS: None

This function sets the communication baud rate for serial port #1 of the controller.
If the display interface is an ML100, the baud rate applies to the control module it
is connected to. If the display interface is an MR100, the baud rate applies to
serial port #1 of the module selected.

MESSAGE NO:

S3-17

APPLIES TO:

Interface Module

DEFAULT VALUE: 1200

VALUE RANGE:

600,1200,2400,4800,9600

DISPLAY MODE:

Advanced

RESTRICTIONS: None

This function sets the communication baud rate for serial port #2 of  the control
module that the ML100 display is connected to. If the display interface is an
MR100, the baud rate applies to serial port #2 of the module selected.

MESSAGE NO:

S3-18

APPLIES TO:

Interface Module

DEFAULT VALUE: alarm:off

VALUE RANGE: alarm:off, alarm:on

flash/on, flash/off

DISPLAY MODE: Advanced

RESTRICTIONS: None

This function determines the response of the alarm light output to an alarm. The
alarm light output is design to drive a 12Vdc LED. If the value is set to “alarm
off”, the alarm light is on in a no alarm condition and turns off when alarms are
present. The “alarm off” setting works best with a green LED for fail-safe mode
where loss of power or a burnt out LED generates an alarm condition. Value
“alarm on”, turns the alarm light off in a no alarm condition and turns on when
alarms are present. Value “alarm flash/on” flashes the alarm light when alarms are
present and turns on the alarm light when there are no alarms. Value “alarm flash/
off” flashes the alarm light when alarms are present and turns off the alarm light
when there are no alarms.

MESSAGE NO:

S3-19

APPLIES TO:

Interface Module

DEFAULT VALUE: MECH:NC

VALUE RANGE: MECH:NO SS:NO

SS:NC

MECH:NO SS:NC
MECH:NC SS:NO
MECH:NC SS:NC

DISPLAY MODE: Advanced

RESTRICTIONS: None

BAUD RATE 2:

1200 

?

ALARM LIGHT MODE:

alarm: off 

?

ALARM CONTACTS:

MECH:NC 

?

   SS:NC 

?

BAUD RATE 1:

1200 

?

BAUD RATE MR100:

1200 

?

Содержание MASTERTRACE















































































































Отзывы:

Нет отзывов

Похожие инструкции для MASTERTRACE

wattio AIR Read Me preview
AIR
Бренд: wattio Страницы: 20
Babybee MIO Manual preview
MIO
Бренд: Babybee Страницы: 28
Hankscraft Runxin HD Series Service Manual preview
HD Series
Бренд: Hankscraft Runxin Страницы: 53
Baby Trend TS42 Instruction Manual preview
TS42
Бренд: Baby Trend Страницы: 24
Baby Trend Navigator Instruction Manual preview
Navigator
Бренд: Baby Trend Страницы: 6
Baby Trend Expedition Instruction Manual preview
Expedition
Бренд: Baby Trend Страницы: 6
C3 Custom Coolers ROVER Owner'S Manual preview
ROVER
Бренд: C3 Custom Coolers Страницы: 16
Nedap WIM Installation Manual preview
WIM
Бренд: Nedap Страницы: 20
T&D TR7 Series Safety Precautions And Instructions preview
TR7 Series
Бренд: T&D Страницы: 2
T&S B-0107 Installation And Maintenance Instructions preview
B-0107
Бренд: T&S Страницы: 5
EasySMX Arion 9110 User Manual preview
Arion 9110
Бренд: EasySMX Страницы: 11
EasySMX Bayard 4108 User Manual preview
Bayard 4108
Бренд: EasySMX Страницы: 8
WAREMA LONMSE 2M230I Operating And Installation Instructions preview
LONMSE 2M230I
Бренд: WAREMA Страницы: 4
HomeMatic HmIP-FAL230-C10 Installation And Operaion Manual preview
HmIP-FAL230-C10
Бренд: HomeMatic Страницы: 42
Desoutter 6159326760 Original Instructions Manual preview
6159326760
Бренд: Desoutter Страницы: 74
jablotron CL-301SL Quick Start Manual preview
CL-301SL
Бренд: jablotron Страницы: 2
2N 9160341 Installation Manual preview
9160341
Бренд: 2N Страницы: 107
Allen-Bradley Micro850 series Installation Instructions Manual preview
Micro850 series
Бренд: Allen-Bradley Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды