Nexo NXAMP4X1 Скачать руководство пользователя страница 78

Страница: 78 / 140

NXES104 EXPANSION BOARD, REMOTE CONTROL AND ASIO DRIVER

(1) Ethersound

™

IN Port

This port features and Ethercon® connector. Use this type of connector to secure your

Ethersound™ network from unwanted unplugs. This type of connector also ensures a

longer life to the internal RJ45 contacts, because it preserves it from external traction.

Use this port as an Ethersound™ IN port when connecting to an Ethersound™ network.

(2) Ethersound

™

network Status LEDs

The two LEDs next to the IN port shows that data is received from the IN port (when the

top one, marked “Rx” blinks) or are send through the IN port (when the bottom one,

marked “Tx” blinks).

NB: When used with mono-directional Ethersound™ network, if no remote control

computer is connected, only the Rx LED of the IN port will blink.

The two LEDs next to the OUT port shows that data is received from the OUT port (when

the top one, marked “Rx” blinks) or are send through the OUT port (when the bottom one,

marked “Tx” blinks).

NB: When used with mono-directional Ethersound™ network, if no remote control

computer is connected, only the Tx LED of the OUT port will blink.

(3) Ethersound

™

OUT Port

This Port features an Ethercon® connector. Use this type of connector to secure your

Ethersound™ network from unwanted unplugs. This type of connector also ensures a

longer life to the internal RJ45 contacts, because if preserves it from external traction.

Use this port as an Ethersound™ OUT port when connecting to an Ethersound™ network.

(4) Remote ES100 port

The ES100 is an upgrade of the original Ethersound™ standard. It offers new functionalities

but can also be downgraded to standard Ethersound™ network for compatibility with older

devices. See bellow for details.

This Remote ES100 port is a remote control port / ASIO input port that is designed to be

used with shared Ethernet LAN (i.e. not dedicated to Ethersound™). Connect the PC

computer(s) running ESmonitor™ and/or the ASIO streamer to this port.

WARNING! Do not use this port if your NXAMP Powered TDcontroller is used in an

Ethersound network with some non ES-100 devices.

On top of this plug you will find 2 LEDS: The left one (Link), means that the equipment is

PAGE 78 OF 140

Содержание NXAMP4X1













































































































































Результаты поиска

Содержание NXAMP4X1

Отзывы:

Похожие инструкции для NXAMP4X1

Бренды по названию

Популярные бренды

Nexo NXAMP4X1, Руководство пользователя

Результаты поиска

Содержание NXAMP4X1

Отзывы:

Похожие инструкции для NXAMP4X1

Бренды по названию

Популярные бренды