Nexo NXAMP4X1 Скачать руководство пользователя страница 97

Страница: 97 / 140

NXDT104 EXPANSION BOARD, DANTE™ PATCHING AND REMOTE CONTROL

NXDT104 expansion board, Dante™ patching and remote control

On the back panel of the NXAMP Powered TDcontroller there is a slot where the user can

easily insert an expansion board to add digital inputs and remote control to the unit.

Since July 2009, all NXAMP4x1s and NXAMP4x4s are shipped with an expansion card fitted

in, the NX-DFLT card. This card prevents output noises when main AC power feeding

NXAMPs is brutally shutdown (ie power down at the end of the show before NXAMPs are

switched off). NX-DFLT card should always be fitted in when no other expansion card is

used.

The NXDT104 expansion board for NXAMP is compatible with the Dante™ network

technology. This board offers 4 digital inputs of 24 bits/ 48 KHz audio data from a Dante™

network, and also remote control of the unit through the PC based application ESmonitor™.

WARNING! Only 48 KHz audio from Dante™ network is supported.

NB: The firmware of the NXDT104 is automatically updated if needed when the firmware of

the host NXAMP is updated (see further in this manual).

NXDT104 Physical description

The NXDT104 is designed to fit the NEXO’s slot form factor that can be located on the back

panel of the NXAMP Powered TDcontrollers.

NB: This slot features an 80-pins internal connector that is not compatible with the Yamaha

mini-YGDAI slot.

(1) Dante™ Primary Port

This Port running at 100 Mb or 1 Gb (automatically selected) features and Ethercon®

connector. Use this type of connector to secure your Dante™ network from unwanted

unplugs. This type of connector also ensures a longer life to the internal RJ45 contacts,

because it preserves it from external traction.

PAGE 97 OF 140

Содержание NXAMP4X1













































































































































Результаты поиска

Содержание NXAMP4X1

Отзывы:

Похожие инструкции для NXAMP4X1

Бренды по названию

Популярные бренды

Nexo NXAMP4X1, Руководство пользователя

Результаты поиска

Содержание NXAMP4X1

Отзывы:

Похожие инструкции для NXAMP4X1

Бренды по названию

Популярные бренды