Neopost MaxiMailer HD Скачать руководство пользователя страница 5

Страница: 5 / 69

MaxiMailer HD Operator Manual

Caution!

Please, read these notes with care.

Save these instructions for later use.

All notes and warnings found on the machine are to be followed.

Important! The machine must be installed only by an authorised

service engineer.

A safe, level position is necessary, when installing the

machine, with sufficient space all round to operate it. The machine is to be

protected from moisture. If moving the machine, ensure that the castor

brakes are

off

, and push on the stand, not the machine.

Ensure there is at least 1 metre of free space between the operator side of

the machine and a wall or barrier. To provide access to the mains switch, the

opposite side of the machine must be at least 150mm from a wall or barrier.

Do not place surrounding furniture or other objects where your path may be

obstructed.

IMPORTanT

For permanently connected equipment, a readily accessible disconnect device

shall be incorporated external to the equipment.

For pluggable equipment, the socket outlet shall be installed near rhe

equipment and shall be easily accessible.

The machine may only be connected to a voltage of 230V/50Hz or 115V/60

Hz,depending upon model.

The mains plug may only be connected with a socket having an installed

protective contact! The protective effect will be compromised by the use of

an extension line without a protective grounding conductor. All interruptions

of the protective grounding conductor, within or outside of the machine,

are prohibited. The device is double pole fused! When fuse failure occurs,

electrical machine parts can still carry voltage. When making the connection

to the mains power, be aware of the connection values on the nameplate.

Inspect the voltage setting on the device’s power input module. Run the

supply lines in such a way, that no-one may trip over them. Do not place any

objects upon the supply line. When the machine is not in use over a long

period of time, it should be disconnected from the power supply. In this way,

damage would be prevented in the event of excess voltage. Protect the device

from moisture. When moisture enters the machine, there is the danger of

electrical shock. Never open the machine except the top cover. For reasons

of electrical safety, the machine may only be opened by authorized Service

Agents.

Never reach into the machine when it is running! This could only occur if a

safety interlock were to fail.

The danger of injuries exists, through pulling in and crushing on the rotating

rollers. In addition, keep long hair and parts of loose clothing far from the

machine in operation.

If a safety interlock fails, your service agent must

be contacted immediately!

In order to prevent damage to the machine, only factory authorized accessory

parts should be used.

Prior to cleaning the exterior of the machine, it should be disconnected from

the power supply. When cleaning the machine, do not use liquid or spray

cleaners, but only a cloth dampened with water.

When cleaning sensors use

only

non-flammable airdusters, eg. part number

E0070A. Other types may use flammable propellants, which could result in fire

or explosion.

Installing

the

machine

electrical

danger

Operating

safety

Cleaning

the

machine

Cleaning

sensors

2.1 General safety notes

Содержание MaxiMailer HD






































































Результаты поиска

Содержание MaxiMailer HD

Отзывы:

Похожие инструкции для MaxiMailer HD

Бренды по названию

Популярные бренды

Neopost MaxiMailer HD, Руководство оператора

Результаты поиска

Содержание MaxiMailer HD

Отзывы:

Похожие инструкции для MaxiMailer HD

Бренды по названию

Популярные бренды