Neopost MaxiMailer HD Скачать руководство пользователя страница 15

Страница: 15 / 69

MaxiMailer HD Operator Manual

5.3.3 To adjust

the envelope

Inserter

settings

Unit fine Tuning

Press on the envelope

inserter on the machine

graphic to display the

fine tuning screen. select

Hardware fine Tuning

display further information.

You can select:

a: The width of the collate

pocket guides.

b: The overall width of the

insert fingers.

c: The time allowed for

the flap to seal before the

envelope is ejected.

d: Adjustment of the point

at which the wetter beam

drops to wet the flap. +ve

increases wetting in 1mm

steps (moves start point

towards insertion area).

e. Adjustment of the amount of envelope travel into the sealing rollers.

+ve = further forward, away from exit direction.

f. Adjustment of the envelope stop position for insertion. +ve = further

forwards, towards exit direction.

g. Adjustment of the amount of insertion of the insert pack into the

envelope. +ve = further forwards past the flap crease.

h. Adjustment of the amount of envelope foward travel after flap

wetting, before reversing to enter the sealing rollers. +ve = further

forward into the output rollers, towards the exit direction.

i. Adjustment of linear speed of pack from collate pocket to output.

By default, pack will travel at maximum possible speed determined by

software. The speed can be reduced to optimise movement of different

materials. Options are Auto/Low/Medium/High (High is the same as

default speed).

j. Adjustment of strength of blower fan for envelope opening. Options

are Off/Low/High (default is low). Use High for single sheet into C4.

cont.

k. The sequence of the inner or outer finger pairs, whether inner

or outer pair enters the envelope first. This slight delay can assist

opening the envelope throat, depending on its design.

Note: Press the ‘Unit’ button in the top left corner to

toggle between fine tuning for unit and hopper.

Содержание MaxiMailer HD






































































Результаты поиска

Содержание MaxiMailer HD

Отзывы:

Похожие инструкции для MaxiMailer HD

Бренды по названию

Популярные бренды

Neopost MaxiMailer HD, Руководство оператора

Результаты поиска

Содержание MaxiMailer HD

Отзывы:

Похожие инструкции для MaxiMailer HD

Бренды по названию

Популярные бренды