UNIVERGE SV8100
Issue 4.1
System Hardware Manual
4 - 77
3.
Connect the cable from the NT1 Network Termination cable to
the CN7 or CN8 connector on the CD-2BRIA blade and/or
PZ-2BRIA daughter board. (Refer to
Figure 4-26 CD-2BRIA
Blade on page 4-75
for the location of the connectors on the
blade.)
5.3.3
LED Indications
LED indications for the CD-2BRIA are listed in
Table 4-39 CD-2BRIA
LED Indications
. Each LED is listed with its associated function and
LED and Operational status. Refer to
Figure 4-26 CD-2BRIA Blade
on page 4-75
for the location of the LEDs on the blade.
With normal operation, the status LED
flashes fast. If trouble was found during
the self diagnostics routine, the status LED
flashes slow.
Once connected, the PKG LED will not be
indicated for the status of Layer 1 Link
.
Table 4-39 CD-2BRIA LED Indications
LED Indication
Operation Status
Remarks
Live LED
(Green)
Busy LED
(Red)
On
On
System Initializing
–
Flash (1s)
On
The assignment of the unit is refused.
When you exceed the system
capacity.
When the main software
version is not matched.
Flash (1s)
Trouble found during self-diagnostics.
–
Flash
(100ms)
On
Normal
Operation
A Channel is busy (use
another from CH1 ~ CHx).
–
Off
All channels are idle.
–
Off
On
Unit Busy
A Channel is busy (use
another from CH1 ~ CHx).
–
Off
All channels are idle.
–
Flash 80ms
(On/Off) x 3/
400mS off
Downloading firmware.
–
Содержание Univerge SV8100
