NEC Super Script 4400 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 317

background image

Using MAP

71

NE

TW

OR

K PR

INTING

U

SING

MAP

The Management Access Program (MAP), runs only under Windows 95/98 and Windows NT 4.0. You use MAP to
list SuperScript 4400 network printers connected to your network. Then you select one to go to its Network
Administration Page for network administration options.

MAP Operating Requirements

To use MAP, you must have installed on your PC
•

Netscape Navigator or Internet Explorer

•

The Microsoft TCP/IP protocol stack, if printer is going to support TCP/IP.

For IPX Search Functions:

The IPX protocol must be installed and enabled on your PC. Both Microsoft and

the NetWare 32-bit stacks are supported. You must log in to the Novell Server.

For IP Peer to Peer Printing:

Both your workstation and printer must have an IP address and subnet mask

entered. If communicating across subnets, the default gateway must also be identified.

For IPX Peer to Peer Printing:

Your PC must have the IPX/SPX compatible protocol installed and enabled.

Installing MAP

MAP is available on the

SuperScript 4400 Series CD

that comes with your printer. MAP must be installed from

Windows 95/98 or Windows NT 4.0. It cannot be installed from the
MS-DOS

®

command prompt.

a. Insert the

SuperScript 4400 Series CD.

b. Use the

Administrator

installation option to install the MAP utility.

«
...
78
79
80
81
82
...
»

Содержание Super Script 4400






























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Super Script 4400

Бренд: Unitech Страницы: 18

Бренд: Unitech Страницы: 26

Бренд: Panduit Страницы: 6

Figure 4 Standalone

Бренд: 3D Systems Страницы: 2

Power Defense PD3

Бренд: Eaton Страницы: 4

Бренд: Lanier Страницы: 6

Бренд: Datamax Страницы: 95

Mark II E-4205e

Бренд: Datamax Страницы: 72

imageRUNNER ADVANCE C350iF

Бренд: Canon Страницы: 102

imageRUNNER ADVANCE C2230

Бренд: Canon Страницы: 12

Бренд: Canon Страницы: 598

Daisy Wheel 410

Бренд: Radio Shack Страницы: 140

Бренд: Parkside Страницы: 104

Бренд: Me3D Страницы: 14

Бренд: M&R Страницы: 36

BIZHUB 8050 CF5001

Бренд: Konica Minolta Страницы: 20

Бренд: Riso Страницы: 82

Бренд: Radio Shack Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды