NEC Super Script 4400 Скачать руководство пользователя страница 259 | Manualshive

Страница: 259 / 317

background image

250

SuperScript 4400 — Maintenance Guide

LCD Message

Explanation

Booting…

First message to appear when the printer is powered up.

OUT OF PAPER

One of the paper trays is empty

TRAY 2 UNSUPPORTED SIZE

Lower tray contains paper size that is not supported by engine.

PAPER MISMATCH LOAD
<Paper Size> TRAY

Paper tray does not have the correct paper size as specified for
the print job. Load the paper size shown on the display <Letter,
Legal, A4, B5JIS, B5ISO, EXEC, FOLIO, FSCAP, SPFOLI,
QUARTO, COM-10, or DL>.

<K, Y, M, or C> TONER EMPTY

Specified toner module is empty. Replace it with a new one.

<K, Y, M, or C> TONER NOT FOUND

Specified toner module is not installed or installed incorrectly.
Reinstall it.

PAPER JAM DRUM

Paper jam in drum area.

PAPER JAM INNER/DRUM

Paper jam in inner area.

PAPER JAM EXIT/DRUM

Paper jam in exit tray.

MISFEED

Paper misfeed.

CHECK WASTE TONER

Waste toner pack is full or is not installed.

REPLACE FUSER OIL

Fuser oil has run out.

REPLACE FUSER ROLLER

Fuser cleaning roller needs to be replaced.

MISPRINT HW FAULT

Printing error caused by no PRREQ-N within a page. ???

photoconductor belt module NOT
FOUND

Photoconductor Belt Module photoconductor belt module is not
installed.

FUSER UNIT NOT FOUND

Fuser unit is not installed.

FUSER ROLLER NOT FOUND

Fuser cleaning roller is not installed.

FRONT COVER OPEN

Front Cover is open.

BACK COVER OPEN

Back Cover (transfer unit) is open.

TOP COVER OPEN

Top Cover is open.

LOW FUSER OIL

Fuser cleaning unit has about 30 pages of operation remaining.

NEAR END FUSER ROLLER

Fuser cleaning roller has about 1000 pages of operation
remaining.

REPLACE BELT

Photoconductor Belt Module photoconductor belt module worn
out.

REPLACE FUSER UNIT

Fuser unit reaches end-of-life.

K-TONER LOW

Black Toner Module has less than 300 pages of operation
remaining.

<Y, M, or C> TONER LOW

Specified Toner Module has less than 500 pages of operation
remaining.

120K SERVICE

Paper discharge, drum cleaner, transfer roller, transfer drum,
and paper pick-up roller all need to be replaced.

CASSETTE OUT <TRAY 1 or 2>

Cassette is not installed in Paper Tray 1 or 2.

MEDIA MISMATCH LOAD <MEDIA>
TRAY

Tray does not have the correct media as specified for the print
job. Load the media shown on the display <Paper, Label, or
OHT (Over Head Transparency)>.

«
...
257
258
259
260
261
...
»

Содержание Super Script 4400






























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Super Script 4400

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 48

Stylus Pro 7900

Бренд: X-Rite Страницы: 36

Бренд: Magicard Страницы: 6

Бренд: DASCO Страницы: 2

Бренд: Lanier Страницы: 265

Бренд: UniFlow Страницы: 42

WorkCentre 7525

Бренд: Xerox Страницы: 70

WorkCentre 7525

Бренд: Xerox Страницы: 8

WorkCentre 7328

Бренд: Xerox Страницы: 24

WorkCentre 7232

Бренд: Xerox Страницы: 4

WorkCentre 7232

Бренд: Xerox Страницы: 24

WorkCentre 7232

Бренд: Xerox Страницы: 236

WorkCentre 7232

Бренд: Xerox Страницы: 128

WorkCentre 7232

Бренд: Xerox Страницы: 25

WorkCentre 7232

Бренд: Xerox Страницы: 8

WorkCentre 7228

Бренд: Xerox Страницы: 22

WorkCentre 7228

Бренд: Xerox Страницы: 300

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды