NEC Super Script 4400 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 317

background image

70

SuperScript 4400 — Maintenance Guide

Unit Status:

Click here to view the current state for each protocol and NIC port available on your NIC. For

each supported protocol (Novell NetWare, TCP/IP, or AppleTalk), the top line displays the protocols
supported and if the protocol is enabled or disabled.

Network Address:

Click here to view the serial number and the Ethernet MAC (Media Access Control)

address for the NIC.

Change Password:

Changing any NIC parameters using the NIC Configuration Menu requires a password.

Click here to change your password. The default password is

sysadm.

Your password can contain letters,

numbers, and punctuation, and is case sensitive.

note:

If you forget your password, you can restore factory defaults manually. See page xx.

Protocol Functions

The

Protocols

feature is for setting up network options and parameters. It provides extensive access to NIC

parameters, and allows you to setup IP parameters (IP address, subnet mask, and default gateway). You can
enable/disable AppleTalk and NetWare, but not TCP/IP. (We recommend that you disable any protocol that you
are not using.)

Other Functions

Test Printer:

Click here, and then click on the

Start Test

button in the dialog box that appears, to send a test

document to the printer.

Configure Status Page:

Click here to configure Network Settings page options. In the dialog box that

appears, select the checkbox by

Print Status Page on Startup

to generate a status page (the Network Settings

page) each time you turn on the printer or reset the NIC.

note:

We recommend that you leave this setting checked to print at power-on.

To print out a Network Settings page immediately, click

Generate Now

.

Printer Status:

Click here to display status information for the printer and NIC, as well as errors and

messages.

«
...
77
78
79
80
81
...
»

Содержание Super Script 4400






























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Super Script 4400

Бренд: NCR Страницы: 36

Бренд: NCR Страницы: 206

Бренд: NCR Страницы: 138

Бренд: Xerox Страницы: 310

Бренд: Samsung Страницы: 165

Бренд: Samsung Страницы: 2

Inkjet SCX-1150F

Бренд: Samsung Страницы: 66

Бренд: Samsung Страницы: 155

CLX-3170FN series

Бренд: Samsung Страницы: 220

CLX 6210FX - Color Laser - All-in-One

Бренд: Samsung Страницы: 36

CLX-3160 Series

Бренд: Samsung Страницы: 139

Бренд: Samsung Страницы: 8

Lazett Combo SCX-4016

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 319

Бренд: QMS Страницы: 26

Бренд: Dascom Страницы: 12

Бренд: Dascom Страницы: 19

Бренд: Dascom Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды