NEC Super Script 4400 Скачать руководство пользователя страница 13

Страница: 13 / 317

SuperScript 4400 — Maintenance Guide

System Requirements

Your SuperScript 4400 printer and software can operate using the following minimum system configurations.

Windows Operating System

•

Microsoft Windows 3.x, Windows 95/98,
or Windows NT 4.0

•

486 or higher CPU

•

CD-ROM drive

•

5 MB of free hard disk space

•

8 MB or more of RAM

•

Parallel Port

•

Ethernet connection (for the 4400N)

MacOS

•

Mac OS 7.1 or higher

•

68040 or higher CPU

•

CD-ROM drive

•

5 MB of free hard disk space

•

8 MB or more of RAM

•

Ethernet connection on the 4400N

Web-Based Printing Requirements

To use the web-based Pull Printing and NEC PrintAgent features, you need to have Microsoft’s Internet Explorer
4.01 SP1 web browser.

Network Printing Requirements

Supported Printing Environments

The SuperScript 4400 comes with software for using the printer on several operating systems and networks,
including
•

Microsoft

Windows

3.x, Windows 95/98, and Windows NT

4.0

•

NetWare

versions 3.x and 4.x

•

Mac™ OS 7.1 and higher using EtherTalk

•

Peer to peer printing for Windows 95/98

•

UNIX

For network setup, your workstation and network operating system should be configured and operating correctly,
and your SuperScript 4400 printer drivers should already be properly installed.

Hardware Requirements

You need to provide the following additional hardware to setup and connect your printer.
•

For standard connection, a IEEE 1284 compliant parallel cable.

•

For network connection, Category 5 twisted pair cable with RJ-45 connectors for 10/100Base-T Ethernet

shown here.

note:

The NIC automatically detects whether you have a 10 Mbps or 100 Mbps Ethernet connection. For better

performance, NEC recommends that you use shielded cable and connectors when connecting to
100 Mbps Ethernet.

Содержание Super Script 4400






























































































































































































































































































































Результаты поиска

Содержание Super Script 4400

Отзывы:

Похожие инструкции для Super Script 4400

Бренды по названию

Популярные бренды

NEC Super Script 4400, Руководство по обслуживанию

Результаты поиска

Содержание Super Script 4400

Отзывы:

Похожие инструкции для Super Script 4400

Бренды по названию

Популярные бренды