NEC Super Script 4400 Скачать руководство пользователя страница 19

Страница: 19 / 317

SuperScript 4400 — Maintenance Guide

DENTIFYING

RINTER

ARTS

Use the illustrations on the facing page to identify standard parts for the SuperScript 4400.

Front View

•

Operator Panel—for displaying messages and configuring the printer

•

Power button—for turning on and off the printer

•

Top Cover—provides access to the Fuser Unit and inside of the printer (also serves as the Output Tray)

•

Output Tray —holds up to 250 printed sheets

•

Top Cover Release button—unlocks and opens the Top Cover

•

Front Cover—provides access to Toner Modules and Toner Collector

•

Front Cover Latch—unlocks and opens the Front Cover

•

Paper Tray 1—standard input tray, holds 250 sheets of paper

Front Internal View

•

Toner Module Racks—holds Toner Modules

•

Toner Collector—collects used toner

•

Paper Transfer Rollers—moves the paper from the inside of the printer to the Output Tray

Back View

•

Serial Number—necessary for warranty registration

•

Back Cover—provides access to clear paper jams

•

Back Cover Latch—lift to open back of printer

•

Filter Cover—contains the Ozone Filter

•

Bidirectional parallel interface—for attaching bidirectional parallel cable from your computer

•

Ethernet interface—for attaching the Ethernet 10/100 Base-T connectors from your network

•

Interface Panel—contains the controller board, hard drive and network interface card (if installed)

•

Power Cord Connector—for attaching the power cord

•

Back Vent—allows ventilation

Back Internal View

•

Transfer Drum—transfers image to paper

•

Registration Rollers—keeps the paper straight

•

Transfer Roller—works with the Transfer Drum to transfer the image to the paper

•

Paper Discharger—removes the static electricity from the paper

•

Transfer Unit—consists of the above four parts

Top Internal View

•

Fuser Unit—uses heat and pressure to adhere the toner image to the paper. Contains two Fuser Rollers.

•

Fuser Oil Bottle—holds the oil that helps adhere the toner image to the paper

•

Fuser Cleaning Rollers—helps keep the Fuser Rollers clean

•

Belt Cartridge—also known as the Photoconductor Belt Module or OPC Unit.

Содержание Super Script 4400






























































































































































































































































































































Результаты поиска

Содержание Super Script 4400

Отзывы:

Похожие инструкции для Super Script 4400

Бренды по названию

Популярные бренды

NEC Super Script 4400, Руководство по обслуживанию

Результаты поиска

Содержание Super Script 4400

Отзывы:

Похожие инструкции для Super Script 4400

Бренды по названию

Популярные бренды