NEC Super Script 4400 Скачать руководство пользователя страница 282 | Manualshive

Страница: 282 / 317

background image

Operating Specifications

IX

FCC Statement

(For United States Use Only)

Federal Communications Commission Radio Frequency Interference Statement.

WARNING!

Changes or modifications to this unit not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

note:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures.
•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from the one to which the receiver is connected.

•

Consult the dealer or an experienced radio or TV technician for help.

Use a shielded and properly grounded I/O cable to ensure compliance of this unit to the specified limits of the
rules.

If your printer is the NEC SuperScript 4400N model or if you have installed the optional Network Interface Card
(NIC), the printer meets the requirements of FCC Class A when connected to an Ethernet cable.

«
...
280
281
282
283
284
...
»

Содержание Super Script 4400






























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Super Script 4400

Бренд: Olympus Страницы: 71

Бренд: IBM Страницы: 60

Бренд: Oce Страницы: 8

Бренд: Konica Minolta Страницы: 2

Бренд: Xerox Страницы: 4

1900N - B/W Laser Printer

Бренд: Kyocera Mita Страницы: 286

ESP Office 6100 Series

Бренд: Kodak Страницы: 94

Бренд: Ricoh Страницы: 269

Бренд: Konica Minolta Страницы: 424

MINI THERMAL RP-3180

Бренд: TVS electronics Страницы: 19

Бренд: L-Mark Страницы: 62

Бренд: Canon Страницы: 88

Бренд: Canon Страницы: 56

Бренд: Canon Страницы: 364

Бренд: Canon Страницы: 32

Бренд: InfoSight Страницы: 35

Бренд: ION Страницы: 32

Бренд: MUTOH Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды