![background image](http://html.mh-extra.com/html/nec/express5800-140he/express5800-140he_service-manual_251225145.webp)
-
129
-
8.3
POST Error Messages
When the power of the server is turned on, POST (Power On Self-Test) automatically runs to
check the I/O board, memory board, processor, keyboard, and mouse. When POST detects an error,
it displays an error message on the display unit screen. (Some error messages are displayed along
with the action to be taken.)
If the error message listed in the table is displayed on the screen, take a measure according to
"Action" column. When several actions are to be taken, determine the action appropriately.
On-screen message
Action
0200 Failure
Fixed
Disk
•
Replace the hard disk drive.
•
Replace the cable.
•
Replace the HDD cage.
•
Replace the I/O board.
0210 Stuck
Key
0211 Keyboard
error
•
Connect the keyboard connector again,
and restart the system.
•
Replace the keyboard.
•
Replace the I/O board.
0212
Keyboard Controller Failed
•
Connect the keyboard connector again,
and restart the system.
•
Replace the keyboard.
•
Replace the I/O board.
0213
Keyboard locked – Unlock key switch
•
Check if the key switch has been locked
(being pushed).
•
Replace the keyboard.
•
Replace the I/O board.
0220
Monitor type does not match CMOS –
Run SETUP
•
Start Setup to reconfigure the monitor.
•
Replace the I/O.
0230
System RAM Failed at offset
0231
Shadow Ram Failed at offset
0232
Extended RAM Failed at address line
•
Check if ECC 1-bit/multi-bit error is
recorded in the system event log. If the
error is recorded, replace the relevant
DIMMs in pair.
After replacement, start SETUP and
execute [Clear DIMM Error].
•
Replace the memory board.
•
Replace the I/O board.
0250
System battery is dead – Replace and
run SETUP
Replace the lithium battery.
After replacement, start SETUP to set the
current time and date.
0251
System CMOS checksum bad - Default
configuration used
This error may occur if the system is
forcedly shutdown during POST.
Start BIOS SETUP to reconfigure the
system.
0252
Password checksum bad - Passwords
cleared
Start BIOS SETUP to set the password
again.
0260
System timer error
Replace the I/O board.
0270
Real time clock error
Replace the I/O board.
0271
Check date and time Settings
Start BIOS SETUP to set the date and time
again.
Replace the I/O board.
Содержание EXPRESS5800/140He
