Nautilus E618 Скачать руководство пользователя страница 85

Страница: 85 / 137

Motorized Lift

Cover

Incline Adjuster Assembly

14. Using a #2 Phillips screwdriver, remove the 3 indicated screws (with

arrows) that secure the Right Shroud. Remove the bottom screws first,

and then the top screw. Slowly remove the Right Shroud.

15. Using the 18mm open end wrench, remove the indicated bolts (with

an oval) that attach the Incline Adjuster bracket to the Lift Motor Assembly.

This will allow the Incline Adjuster Assembly to pivot.

16. Observe the cable routing from the Motor Control Board (MCB)

Assembly on your machine.
• Power Inlet Cable (Power switch to MCB)

• Lift Motor Cable, Lower (Lift Motor to MCB)

• Lift Motor Cable, Upper (MCB to Console)

• Servo Motor Cable (MCB to Servo Motor)

• Speed Sensor Cable (Speed Sensor to Servo Motor)

• Input/Output (I/O) Cable (Servo Motor to Console)

Note: Be sure to note where all cables are routed for re-assembly.

17. Remove the zipties that hold the cables.

18. Using a short #2 Phillips screwdriver, remove the indicated screws (by

arrows) from the MCB cover. Carefully remove the MCB cover.

NOTICE:

Do not crimp the cables.

Zip Ties

Power Inlet Cable

Speed Sensor Cable

Upper Lift Motor Cable

Input/Output (I/O)

Cable

Lift Motor Cable Servo Motor Cable

MCB Cover

Содержание E618










































































































































Результаты поиска

Содержание E618

Отзывы:

Похожие инструкции для E618

Бренды по названию

Популярные бренды

Nautilus E618, Руководство по обслуживанию

Результаты поиска

Содержание E618

Отзывы:

Похожие инструкции для E618

Бренды по названию

Популярные бренды